20 Most Recent
2005 Dodge Ram - Page 5 Questions & Answers
My 2005 Dodge Diesel flashed Lampout on the way
Hi I'm litoshop, if the lamp out flashed then you have a light bulb that burned out check all the bulbs head light, parking lights, brake lights and signal lights, tail light, plate lights must likely one of those bulbs burn out good luck. if this information has been useful please let us know thank you.
I have my truck at the dealership garage now, and
No, I would refuse any thing other than the oil change. Remove the wheel and inspect the brake linings, that will give you an indication whether you need to look for another place to change the oil, or do it your self. Air cleaner you can replace yourself, transmission fluid and filter you can change yourself. Also brake pads you can change yourself.
Change Dodge Ram tail lights from 2005 to new 2008
I just got a pair of 2008 tail light lens for my 2002 Dodge Ram 1500. If you look under the rear there is a connector that runs up to the tail light. This is a small harness. I believe that all you need to do is purchase the 2008 tail light harness. It looks like it will snap into the bottom of the stock harness and will fit the 2008 lenses.
Removing tailght lenses cover?
drop the tail gate and there are screws where the gate was and if i remember correctly they are torx screws and u just pull straight out the whole cover cause it's clipped into place. when u have the whole tail lamp in your hands unplug the power connecter then use a phillips and unscrew the housing and replace the bulbs. The bulbs are a real pain in the *** cause they have that small little metal piece that breaks all the fricken time. well it does for me anyways. good luck
Windshield wiper
look to see if the clip is broke or missing look between winshild and hood
Won't start
Hi, I understand you have a problem with the alarm.
If the alarm is activated, and if the alarm is aftermarket you have a valet switch , That you can use to deactivate, or put in by pass. just you need to locate, is a little switch going from the alarm module to a dash or any strategic location.
When you found turn the key to run position them move or press the switch. and everything has to stop blinking.
If you are unable to find the switch, put the in on position,
Them go to front and remove the negative battery cable, wait 1 minute and reconnect, them try to start.
But if the alarm is a Factory alarm and you don't have the remote control. you can try deactivate with the key in the door lock cylinder. turning from lock to unlock position.
But remember this model of trucks, they use a chip on the key
If you don't have a key with chip it's gonna do theis problem.
I hop this solve your problem. Thank for using fixya.
Check engine light
P0404 Exhaust Gas Recirculation Circuit Range/Performance
P0405 Exhaust Gas Recirculation Sensor A Circuit Low
I would check out the sensors on the EGR line.
A chilton manual at the auto parts store should show you how to test the sensors along with the test values. It should run about $20
2005 dodge ram 1500 cd issues
If it does the same thing with other CD's then the mechanism inside the radio will need repaired. The dealer can send it out to be repaired or you might ask if the have a "take out" unit of the same model when another cuatomer may have upgraded their system.
2005 dodge diesel codes!
Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.
The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.
After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...
Ok... I hope this help on your problem..
Thank you for use Fixya...
05 Diesel Ram codes, what do they mean?
go by autozone or a local dearlship and they can tell what the codes or and autozone will pull the codes and clear them they might be as simple as a gas cap was left off they are powertrain codes
2007 dodge ram blinker arm
Disconnect battery for 5- 10 min. remove trim panel @ steering column behind steering wheel, remove air bag, steering wheel do not move clock spring tape if need to it will be a black round thing that connecters go to then remove clock spring then blinker arm
Cant say runing
ck' fuel press.@ fuel rail,does it have ck'engine lt. on?..-have it scanned,it does not cost much,..ck' mass air sensor,catylitic converter[plugged]...kev-mn.
Not finding what you are looking for?