20 Most Recent 2003 Buick LeSabre Questions & Answers

Question edited for clarity and typo.Question moved to model category.Duplicate question deleted. Refresh page to see your question.A number of ideas here, low oil, valve lifters and also serpentine belt wear.https://www.google.com/search?q=2003+Buick+LeSabre+has+a+ticking+noise..

Question edited for clarity. Question moved to model category. This seems to cover it.

On my 2003 buick lesabre the rear end of the car sits too ...

JustAnswer https://www.justanswer.com > Buick Repair Apr 9, 2010 - Most likely you issue is the "level" sensor itself. The purpose being when you add weight to the vehicle in the rear, the sensor will tell the ... 1 answer · Top answer: Hello Mr. Dave, Yes, I can see where that would be confusing. I should have... ..

Yes if you want to.

I had this problem, but only on the driver's side (with leather seats). Sometimes the switch would come on, but I could not get it to go back off (and the seat would not heat).

I ended up removing the drivers front seat cover (only the bottom part), folding it back from the driver's door to the middle of the car. You also have to unplug the wiring harness underneath the seat. I found a black spot burned in the foam. This is where a wire had broken. I carefully pulled the wire together, then soldered it. I put everything back together, and it has been working ever since (about 6 months - and getting lots of use in the middle of the winter).

I think the only way to replace the heated seat wires is to replace the whole seat cover. I was glad I could fix mine by soldering it.

It could be the switch. Check this though that I found Wire broken in wire harness that follows right rear trunk arm. It is a common problem. https://www.google.com/search?q=2003+Buick+LeSabre.+I+have+no+tail+lights ..

Question edited to add maker. Question moved to sub category. Check out the videos Michelle https://www.google.com/search?q=2003+buick+lesabre+wiper+motor ..

if there is an access plate you can remove then yes. but generally you have to drop the tank to get to it

Robert

Access panel in the trunk floor, lift up the carpet towards the back seats

You can try disconnecting the Negative battery cable for at least 20 seconds, see if that works. If not, you'll need a scan tool

The battery is under the back seat .

I have a 2003 Buick lesabre limited my inside lights don't work

On this website you find ruse box diagram and description for Buick LeSabre (2003) Buick LeSabre 2003 2004 fuse box diagram CARKNOWLEDGE

On this website you find ruse box diagram and description for Buick LeSabre (2003) Buick LeSabre 2003 2004 fuse box diagram CARKNOWLEDGE

The proper thing to do would be to hook up a factory or professional type scanner an check input data to the PCM from the Transmission internal mode switch . Error means the instrument cluster is loosing data from the PCM - engine computer . The lever assembly-manual shaft detent with internal mode switch (IMS) is a sliding contact electrical switch assembly that corresponds to the PRNDL position selected. Each of the PRNDL positions has a unique ground pattern on four wires from the PCM. The assembly consists of two major components: • The internal mode switch that consists of: - The housing (1), which makes up the stationary contacts. - The insulator (2), which makes up the moving contacts and is secured on the detent lever (4). • The lever assembly which consists of: - The manual shaft (3) - The detent lever (4) The range detection is accomplished by securing the moving contacts to the detent lever. When the driver selects a PRNDL position, the detent lever inside the transmission rotates. This rotates the insulator which in turn grounds the four wires in a unique pattern for each gear selection, corresponding to the PRNDL position selected. The IMS is electrically connected by five wires (four of which the PCM supplies voltage to and one wire that is a common ground) to the transmission pass through connector. Range Selector Displays Incorrect Range The transmission internal mode switch (IMS) is a sliding contact switch attached to the selector detent inside the transmission side cover. The four inputs to the PCM indicate the position of the transmission range selector. The input voltage level at the PCM is high, B+, when the IMS is open and low when the switch is closed to ground. The four input parameters represented are Signals A, B, C and P, Parity. Refer to Transmission Internal Mode Switch Logic . Install a scan tool. Turn ON the ignition, with the engine OFF. Select IMS on the scan tool. Place the range selector in each transmission range: P, R, N, D4, D3, D2 and D1. Does each range selected match the scan tool IMS display? -- Go to Intermittent Conditions in Engine Controls - 3.4L Go to Step 2 2 Select IMS A/B/C/P on the scan tool. Place the range selector in each transmission range: P, R, N, D4, D3, D2 and D1. Does the IMS A/B/C/P display the specified values for each range? Your best bet , take your vehicle to a qualified repair shop.

The root cause can be a failed radiator fan relay, bad water pump or a blown head gasket. But the fact that you can't get the cap back on is troubling. Call a tow truck. Trying to drive this when it's overheating can destroy the engine. A tow is always cheaper than a new engine

if you have a code reader available,reset trouble codes,if that doesn't work you probably need to have it checked out.they may have dis lodged a sensor when they changed the tires.unless you radically changed tire size it shouldn't be the tires

Here's the link and I'm sure you will get the solution of your problem 2003 Buick

Have the problem system checked for proper ground. It may be at the fuse box if it got wet. Electricity and water mean corrosion when there are two metals present - usually copper and iron. When electrical boxes or connections get 'warm' it means that there is added resistance in the circuit causing the heat. (like a light bulb without the light)

How is fuel gauge?going up and down?