20 Most Recent 2004 Mitsubishi Galant Questions & Answers


Wiring, schematic, electrical diagrams, fuse diag, error codes etc are basic contents of these online books they sell here on this website www.reliable-store.com I have attached. Must check it out

2004 Mitsubishi... | Answered on Mar 14, 2018


Interesting problem, especially since its been happening since the car was new. Researching this I found one suggestion that a front wheel bearing is in backwards, and this causes the ABS wheel sensor to read incorrectly until the TCL/ABS computers calibrate themselves.

This is an odd suggestion, as the wheel bearing and hub are an integral assembly. A part photo shows a "normal" looking bearing that only fits one way. A bearing installation problem is not impossible however. There could be dirt/road debris on the sensor, the sensor could be slightly misplaced, or faulty. The TCL/ABS computers read the signals from the wheel sensors, and has diagnostic outputs, which should include indications of poor or missing data streams from all four wheel sensors.

This is the first step to finding a solution. If the TCL/ABS computers are reporting errors from one wheel, then that wheel has to be disassembled to see what's the cause.

2004 Mitsubishi... | Answered on Dec 26, 2017


Both fuel pump relays probably are plugged into the junction block.

2004 Mitsubishi... | Answered on Dec 13, 2017


If the sensor didn't fix the problem, then it's most likely a wiring harness issue. A bad sensor/harness will turn off the ABS & traction control and turn on both ABS and Traction lights. time to troubleshoot the wiring harness for continuity/short between the sensor and the computer.

2004 Mitsubishi... | Answered on Nov 18, 2017


Check the battery pols conection

2004 Mitsubishi... | Answered on Nov 02, 2017


next time take it to a accredited professional shop that will read the fault codes first before advising you on what has to be replaced and not just guessing the problem

2004 Mitsubishi... | Answered on Sep 09, 2017


Hello Edward Garcia,

Indeed yes... you have a 2004 Manufacturer
RECALL CAMPAIN... Notice SC-04-002

FIRST technical Service Bulletin I looked at...

ETACS-ECU Excessive battery drain...

Gives the location and required
>> dealer RE-programming of keys & fobs...

Principally presents on cars left sitting for 7 to 10 days
((they were talking "NEW" cars... I imagine those dynamics change SIGNIFICANTLY with old batteries))...

Attributed to POOR PROGRAMMING...

REMEDY: replacement

Location.. lower dash... between steering wheel & door

Use the FREE TSB database ... provided by
BBB Industries...
(registration is required: these are REAL DOCUMENTS)

http://bbbid.com/

Hope this helped

Carnac the Magnificent

2004 Mitsubishi... | Answered on Jul 19, 2017


Check the brushes on the blower motor that circulates the air in the car.

2004 Mitsubishi... | Answered on Mar 29, 2017


What was the code number? Could a circuit code. Could be no sensor return code. Problems would be sensor, wiring, PCM, or broken cam/crank belt.

2004 Mitsubishi... | Answered on Oct 29, 2016


Have you checked the fuel pressure, are you sure the pump is the issue? Have you run a fault code test on the engine control unit for fault codes? If not do that.

2004 Mitsubishi... | Answered on Oct 19, 2016


compression test cyclinder may have cracked head or warped head .I think that car has an Astron motor from my memory which has an alloy head that can warp or crack if the engine has been overheated ?

2004 Mitsubishi... | Answered on Oct 01, 2016


the causes for the small leak are listed as
hose connections --intake leak--- EVAP canister--- EVAP canister purge valve
check hoses for small cracks ( old hoses) or replace the purge valve

2004 Mitsubishi... | Answered on Sep 19, 2016


I have a 98 Montero Sport. My wipers paused and went then they stopped completly. Come to find out the grease inside the wiper motor had dried out so I put some grease in it and walla works like new. Better then spending 200 on a new wiper motor ^_^

2004 Mitsubishi... | Answered on Feb 08, 2016


It is integrated in your entire electrical system of your vehicle. the only way to bypass is to get an aftermarket alarm with a bypass module which will require an additional ignition key (which is inserted into the bypass module).

2004 Mitsubishi... | Answered on Feb 08, 2016

Not finding what you are looking for?
2004 Mitsubishi Galant Logo

443 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Galant Mitsubishi

  • Galant Mitsubishi

Most Popular Question

changed whole head gasket 2004

  • Cars & Trucks
Loading...