20 Most Recent
2006 Chevrolet Trailblazer - Page 3 Questions & Answers
2006 buick rainer obd code30
in 2006 there is no obd system even code 30 your system is obd2 and code start with P????obd system stop in 1995
2006 Trailblazer LT with power
I think you're in luck. There is a recall for the master switch due to this very issue. Act like you don't know what's wrong, they'll need to replace it to an updated one that won't be so prone to water infiltration.
Posted this as a comment, but wanted to put it out
If you can get the front part of the old case off and the new case matches it, you should be able to use and install the front part and doors from the new one without removing any lines. If the whole case has to come out, all lines (AC evaporator, heater core) have to be disconnected.
My 06 trailblazer cuts off while driving and would cause this problem
Hi Patricia , does it start right up again or do you need to let it sit for a while ? Also how long do you drive till this happens ? There are a lot of electrical sensors on you vehicle , anyone of them could be going bad ,shorting out when it gets hot . Also is the check engine light on ? The main thing , when does it happen , anytime , after wramed up , cold etc...
2006 chevy trail blazer cruise contol does not work. Cant find a fuse under hood or under back seat. Help
Your owners manual should show you where the fuses are located. If you don't have an owners manual, you can go to
my.gm.com, type in your year--make--model and hopefully read your owners manual for free.
Do the brake lamps work ok?
I found these fuses, not only check fuses, check for voltage on fuse circuit, use a test light. Some fuses are hot all the time, some go hot with the key on.
Any codes for the cruise system?
Where is low idle sensor on 2006 chevy trailblazer six cyl it idles low and was told to clean sensor
Just my opinion, I'd check for applicable trouble codes, first. Some of the national brand auto stores will check codes for free. If you want to check codes, yourself, at the least, you need an obd2 code reader that will check po codes as well as manufacturer specific codes. See if anything points to tac/throttle actuator control?
There are also accelerator pedal position sensors that you need to check. If you want to clean throttle body, that's fine.
Where is the ecm fuse for a 2006 trailblazer ls
The fuse box in the engine compartment ! It's marked on the inside of the lid . There are a couple of them ,plus a relay PWR/TRN relay #57 . Now then if you tell use the problem we could be a little more exact !
I have a wrench with a car swerving light up every
{: ) A car swerving light on the instrument cluster is the StabiTrak indicator, sometimes called the traction control indicator. A wrench beside it tells it requires servicing.
Your vehicle is equipped with StabiliTrak, which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Traction control activates when the controller senses wheel spin. StabiliTrak will selectively apply the brakes and reduce engine torque to help regain traction.
Stability control activates when the controller senses a discrepancy between your intended path and the direction the vehicle is travelling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to help guide the vehicle in the direction which you are steering.
When you first start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle. If driving conditions delay system initialization, the STABILITRAK NOT READY message may be displayed. If this is the case, your vehicle does not need servicing.
When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event.
You may also feel or hear the system working. This is normal.
StabiliTrak will turn off automatically if a problem is detected in the system. The StabiliTrak light will come on and SERVICE STABILITRAK will be displayed on the DIC. For vehicles without a DIC, the StabiliTrak light and the StabiliTrak service light will both come on. If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, you should see your dealer for service.
Not finding what you are looking for?