20 Most Recent 1996 BMW 318 Questions & Answers


You actually need the thermostat in to pressurize your cooling system or the coolant won't cyle through the radiator, it'll just cycle around the engine. Most people think without the thermostat in the coolant will just pump freely through the engine and radiator, but it doesn't.

Chuck in a new thermostat, purge the air out of the system and see if it overheats then. I gaurentee it won't, if it does then you've got head problems (but they should already be obvious by now).

1996 BMW 318 | Answered on Jan 09, 2019


The key doesn't turn at all. Not even one click!!! the tumblers are completely jammed. I also just bought the Bently service manual but they don't offer a solution to my problem. I have been searching the web for days and at this stage I know I have only one of two solutions: to drill a small hole where the entry for the pin should be if the key would've turned, then use a pin to remove it; or drill straight through the center of cylinder to destroy the lock tumblers and then turn it to line up with the pin hole, and use the classic method to remove it. Before I attemp either, I need to know if anyone tried them and which one will work better or work at all? I already ordered a new cylinder from dealer so the problem is in removing the old one. Help please.

1996 BMW 318 | Answered on Oct 24, 2018


possible air mass meter fault or split concertina air hose between airr flow meter and manifold

1996 BMW 318 | Answered on Oct 24, 2018


it sounds like the headlamp replacement has caused the problem you have. go back and get the work checked or get a good auto electrician to help

1996 BMW 318 | Answered on Feb 22, 2018


Did you replace the thermostat? Sounds to me like it may be stuck closed.

Have that checked out.


helpful-rowrfu10slju0iejfqxy2apg-1-0_15.png

1996 BMW 318 | Answered on Feb 08, 2018


Sounds like the radiator is clogged up. I would try to flush it or, replace it.
flush bmw radiator YouTube

1996 BMW 318 | Answered on Jan 20, 2018


Shorted wire to sensor. Find a different mechanic!

1996 BMW 318 | Answered on Jan 04, 2018


I, feel sorry for you, after reading your problem, but don't worry you visit the Reliable-Store they will help you for sure. Land Rover Freelender 2002 TD4 Workshop Service Repair Manual

1996 BMW 318 | Answered on Nov 14, 2017



Well, I think I've finally won my 'No Start When Hot' battle!! After pulling my hair out for months, I ended up using a combination of the pointers listed above.

I had already cleaned the battery terminals, starter terminals, terminals at the alternator, and especially the ground connection from the engine block to the engine mount support arm to the chassis. Even after trying two other used (but good condition) starters, I had still been unsuccessful in resolving the issue.

The final two things that I believe did the trick were:
1. I finally remembered/realized that the positive cable from the battery first goes into and out of the B+ jumper box before going on to the starter. Since, I hadn't touched it yet, I dismantled it and took wire brushes to all four connections (MAKE SURE TO DISCONNECT THE BATTERY FIRST!!!)

2. Also, I got two big 'U.S. quarter sized' washers and placed one in between each of the starter lobes and the transmission bell housing in order to provide just a fraction more clearance to the flywheel (This is what I believe the main problem was in my case - mechanical clearance just as stated in one of the previous posts)! I finally came to believe this theory more and more because in order to start my car, sometimes if I rolled it just a few inches in neutral and then dropped the clutch in gear, I would then be able to take the car back out of gear and get it to start (almost as if the flywheel had to move just a tad bit to the right position for the starter to engage more easily).

It's now almost mid-August and I still haven't had any problems from the 'original' starter after approx. 7 months!!
Additional advice: Stick with Bosch starters!!

...Hope this helps someone else out there..

1996 BMW 318 | Answered on Nov 07, 2017


My guess would be the mass air flow sensor, but unfortunately there's

1996 BMW 318 | Answered on Oct 22, 2017


hi
whats the problem with the car?
steering being light is not a fault.
thank you

1996 BMW 318 | Answered on Oct 01, 2017


dounds like maybe your thermostat is not openin properly. maybe slightly but not all the way . i had the same problem a year ago!

1996 BMW 318 | Answered on Sep 20, 2017


problem with the window actuator assembly , will need to strip out to see the exact problem

1996 BMW 318 | Answered on Jun 08, 2017


run the fault codes
could be a problem crank /cam position sensor or wiring harness or connection problem

1996 BMW 318 | Answered on May 27, 2017

Not finding what you are looking for?
1996 BMW 318 Logo

997 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1999 BMW 318 ti
1999 BMW 318 ti

509 Questions

1997 BMW 318
1997 BMW 318

395 Questions

2002 BMW 318
2002 BMW 318

14 Questions

2003 BMW 318
2003 BMW 318

8 Questions

1994 BMW 318
1994 BMW 318

-6 Questions

Top BMW Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

80stech

Level 2 Expert

120 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

318 BMW

  • 318 BMW

Most Popular Question

intermittent heater fan

  • Cars & Trucks
Loading...