Top 20
2001 Nissan Maxima Questions & Answers
2001 maxima alarm not working but panic works
ck for a fuse in the under the hood fuse box that says bsm may be blown.
Also try this.....
To reset the security system remove the negative battery cable for 30 minutes, then reconnect the cable. Next, lock and unlock the doors using the remote. This will reset the alarm system and the engine will start and fobs reset.
Here are some factory notes....FYI
Anti-Theft Systems
PROGRAMMING
NOTE: If a new Smart Entrance Control Module (SECU) is installed, a new identity code must be entered and all remote controllers must be programmed. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
PROGRAMMING > PROGRAMING NEW ID CODE
NOTE: This procedure will erase all previous identity codes and render all previously programmed remote controllers inoperative (until reprogrammed). All remote controllers to be used with system must be programmed at the same time. A maximum of 4 remote controllers can be programmed. Any attempt to program more than 4 controllers will be ignored. If same identity code is entered more than once, entry is ignored even though hazard warning lights will still flash twice.
1. Close and lock all doors. Erase original identity code(s) by inserting and completely removing key from ignition switch more than 6 times within 10 seconds. Hazard warning lights should flash twice. Turn ignition switch to ACC position.
2. Push any button on new remote controller once. Hazard warning lights should flash twice, indicating identity code has been entered. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
3. For each additional remote controller to be programmed, manually release door lock and lock again by using door panel switch and repeat step 2. If no additional remote controllers are to be used, exit programming mode by unlocking and opening driver's door.
Please let me know if you need anything else to get the problem fixed. Happy mew Year!
2001 Nissan Maxima service engine light stays on code from Auto Zone scanner is PO139 and PO138. What should my next step be to solve this problem.
code p 0138 refers to 2 items
1--heated oxygen sensor(HO2S) 2 bank 1--high voltage ==causes --wiring short to positive --HO2S---ECM
2--oxygen sensor (O2S) 2 bank 1--high voltage ===causes wiring short to positive ---ECM
code p 0139 refers to 2 items
1--- heated oxygen sensor (HO2S) 2 bank 1--slow response ===causes --heating inoperative --wiring--ECM
2--oxygen sensor (o2S) 2 bank 1 slow response ===causes --wiring --- O2S
heated oxygen sensors9HO2S) are in the exhaust manifold before the cat converter
Oxygen sensors (O2S) are after the cat converter
it is indicated that the HO2S is faulty-
check the wiring and /or replace both sensors
2001 Nissan Maxima loses power at 40 MPH.
Fuel pump is not pumping hard enough anymore. Have a mechanic check the pressure. Either pump is bad or the fuels filter is clogged. One other thing that causes this is a clogged Calalytic Converter.
Can a iac for 2001 nissan maxima be cleaned?
Get a second opinion. That is some crazy money to spend, but you should have expected that from a luxury model like the Maxima. I am surprised that a 2001 model would need the IAC programmed, but it could be. I would want a second opinion.
My 2001 maxima security light flashing won't start with either one of my two keys
Does your ignition key have an electronic chip? Sometimes with normal use the finish can wear off near or on the electronic chip. Typically, this will result in the car failing to start and security flashing or just lighting up on your dash panel. The problem is your anti-theft prevention unit can't read the chip. You need to contact a dealership. They will program a new key.
Not finding what you are looking for?