2006 Pontiac Torrent - Answered Questions & Fixed issues

Engine Coolant Temperature (ECT) Sensor At the rear of the engine cylinder head, below the brake master cylinder

It is likely to be neither! It was running at the correct temperature before, so all was good, you just has a leak that needed fixing. Your problem is likely cause by air in the system which is preventing coolant circulation. Make sure your radiator fans come on once the engine comes to temperature, as the coolant sensor must have been removed. https://www.fixya.com/cars/r29872074-vehicle_cooling_system_no_heat ..

SOUND LIKE HEATER CORE LEAKING COOLANT INSIDE VECHICLE.

What's the "TC" sign? Guessing from the rest of your question, it sounds like your throttle body is dirty. try to clean it with throttle body cleaner & see if that helps.

Hi, your car's heater core might be malfunctioning or their might not be enough coolant (or hot coolant) to heat the inside of your vehicle. Please first ensure that your coolant is not running low (if so, you can add more) and then allow a place like autozone to perform a quick check on your heater core to see if it needs to be replaced. Thank you.

https://www.obd-codes.com/p0171

drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

The one that fits :>) You need a full socket set for jobs like that. 30mm Dorman - Autograde - Staked Spindle Nut M20-1.5 Hex Size 30mm (sold by each) (Part No. 615-089)

2006 Pontiac Torrent Spindle Lock Nut ' Advance Auto Parts

https://www.google.com/search?q=2006+Pontiac+Torrent.+Socket+size+for+axle+nut ..

Wheel bearings, brakes binding, rear axle etc etc etc Have a look . Jack up the vehicle or take it to a garage for inspection.

https://www.700r4transmissionhq.com/pontiac-torrent-brake-lights-not-working/ https://www.justanswer.com/pontiac/3hh64-2006-pontiac-torrent-brake-lights-dont-work-checked-fuse-its.html

Many wiring harnesses are premade to be used in a number of model packages. For instance your model may have a 'Tow Package' and this wires may be part of that, or the top model may have a backup camera, and it is the power to it. As long as everything works, just tape it up out of the way.

Could be a heater control module, wiring issue, or the bulbs have burnt out. Hard telling without looking at it.

This is already covered in this site. See the following link. Questions Answers for Pontiac Torrent off oil pan

heater core could be out . is you thermostat in still?? and when turning the heater on is the car already warmed up??

I'm having the same problem but I changed the caliper also and after 1 hour of bleeding the lights starting with the rear right tire and no more air is coming out I still have a very soft brake paddle.

No, not a fuse issue. Either the speakers aren't wired correctly of there is a wire loose somewhere.

Take it back and have them reset the oil change reminder.

Some fixya user told me a website reliable-store it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

I got this free Pdf man ual from reliable-store for free and I don't think Ive visited a mechani c or fixya for help for more than 3-4 times out of the 20 times I fixed the chipper in these 4 years