2006 Mazda Tribute - Answered Questions & Fixed issues


There's a website reliable- store
all heavy equipment repair issues servicing, loading, wiring, engine problems everything is covered here its a must try for those who aren't fully equipped with tools or knowledge

2006 Mazda... | Answered on Feb 12, 2019 | 59 views


Sounds like brake pedal switch

2006 Mazda... | Answered on Jan 05, 2019 | 341 views


The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

2006 Mazda... | Answered on Jun 14, 2018 | 62 views


steering idler sounds like its worn, on the steering you will see a link that goes from the steering arm just before the tracking, looks like a swing, it attaches to the body shell and has a bolt and rubber innards, this dampens down the vibration on the longest arm to the wheel so on right hand drive its on left wheel on left hand drives its on the right side, should not have a lot of play in it but should move left to right depending on steering position. cirb clipping wears them out quicker and so does pot holes in the road.

2006 Mazda... | Answered on Nov 11, 2017 | 93 views


Fixya does not sell parts and cannot locate sources.

2006 Mazda... | Answered on Aug 06, 2017 | 93 views


Under the hood in the fuse and relay center.

2006 Mazda... | Answered on Sep 04, 2016 | 104 views


If you ran the MC dry, you may have sucked in a ton of air. If you're sure the system is now completely sealed you have to just keep pumping and bleeding, preferably starting at the right rear brake, then to the left rear brake, the right front and finally the left front. Sometimes no matter how much you pump the air will not come out, then you have to use a mighty VAC and power bleed the system.

2006 Mazda... | Answered on Feb 08, 2016 | 88 views


Hi I am a tech mechanic I deal with things like that Evey day lol but sounds like the anti theft or the ignition switch n lock n key to but you also have broke wires touching even in thecolom

2006 Mazda... | Answered on Oct 23, 2015 | 260 views


Check these three things in the misfiring cylinder: spark, gas, and compression. One of them is wrong or missing. For spark check the spark plug and wire. Make sure you have spark on the plug wire, a strong blue spark. For gas, the fuel/air mixture may be wrong. Does the fuel injector pulse, putting gas into the cylinder? Possibly you may have a leaking injector or a clogged injector.

If gas and spark seem okay, you need to check compression in the cylinder. Low compression will cause a misfire. If compression is 20 or 25% lower than adjacent cylinders, that could be causing a misfire. For example, say numbers 1 and 3 cylinders had about 150 psi compression. 80% of 150 = 120, so if cylinder 2 is 120psi or less, that could be setting the misfire code. Low compression can be caused by valves not seating well, or bad piston rings, bad head gasket- something in the combustion area of the cylinder is losing compression.

2006 Mazda... | Answered on Aug 17, 2015 | 219 views


It may just be a coil breaking down or a bad spark plug. Try swapping one of the coils over with the faulty one and see if the misfire happens on that cylinder and cylinder 2 runs fine. If it does then swap the faulty one for a new coil. Don't know about your car but most now have individual coils for each cylinder that fit directly onto each spark plug.

2006 Mazda... | Answered on Aug 17, 2015 | 90 views


Check for power with a test light with the light connected. If you have power then its the ground. If no power then you will need to trace the wire back to find break. As I recall they did have seperate fuse for left and right headlight high & low beam. Also did you get a defective new bulb?

2006 Mazda... | Answered on May 31, 2015 | 475 views


Most likely, your inertia switch has been tripped, either due to an accident or a sudden jolt to the vehicle.

2006 Mazda... | Answered on May 14, 2015 | 140 views


  • fuel rail pressure sensor could be the pressure regulator on the fuel rail a big vacuum leak

2006 Mazda... | Answered on Mar 26, 2015 | 199 views


ABS does not say differential that will be the brakes

2006 Mazda... | Answered on Feb 28, 2015 | 86 views


Check the glove box light,make sure it goes off when closed.

2006 Mazda... | Answered on Feb 20, 2015 | 155 views


Hi Allen,

It is located behind the power steering reservoir. Attached a video to show you how to access it.

Good luck.

2006 Mazda... | Answered on Feb 07, 2015 | 842 views


May have spilt some oil on the exhaust manifold should burn off in a short time if not check for a oil leak around the exhaust.

2006 Mazda... | Answered on Dec 26, 2014 | 79 views


Did you check for OBD Codes?

Did you have a shop drive it with scanner,
& see if all the Emission Monitors have run?

Ever do any Preventative Maintenance, or just
drive your vehicles until you have problems !

Did you check for fuel pressure at the motor & spark ?

Battery Dead or worn out !

No one can guess at your vehicle issues-- without it-- to
do some testing,always been that way

2006 Mazda... | Answered on Sep 21, 2014 | 73 views


try changing the fuel filter

2006 Mazda... | Answered on Sep 21, 2014 | 52 views

Not finding what you are looking for?
2006 Mazda Tribute Logo

275 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...