2008 Hummer H3 - Answered Questions & Fixed issues
My 2008 hummer h3 got C0136 Base brake system pressure circuit error on DTC and displays waning Traction off, Service stab sys. Whats the exact problem and any part to be replaced?
DTC C0136: Base Brake System Pressure Circuit
The electronic brake control module (EBCM) monitors an internal input from the master cylinder pressure sensor to enhance antilock brake system (ABS) braking and vehicle stability if equipped.
Conditions for Setting the DTC
• When vehicle speed is more than 7 km/h (4 mph), the master cylinder pressure does not change for 30 seconds with the brake applied.
• When vehicle speed is more than 10 km/h (6 mph), the master cylinder pressure signal is erratic.
• Master cylinder pressure signal is out of range.
• Master cylinder pressure is high for 5 seconds with the stop lamp switch signal OFF.
Action Taken When the DTC Sets
• The EBCM disables traction control system (TCS) and vehicle stability enhancement system (VSES) for the duration of the ignition cycle.
• A DIC message and/or a warning indicator may be displayed.
Diagnostic Aids
The master cylinder pressure sensor is located internally in the Master Cylinder and is not serviceable.
Circuit/System Verification
Important: It is recommend that the defective components be replaced, and not the complete brake master cylinder assembly.
Verify that DTCs C0131, P0719, P0724 are not set.
? If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.
Replace the EBCM.
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for EBCM and BPMV replacement, setup, and programming
Your best bet , take it to a qualified repair shop.
2/22/2019 5:59:10 PM •
2008 Hummer H3
•
Answered
on Feb 22, 2019
•
2,187 views
How much differential oil and type for H3 hummer 2008 5cyl
for help u will find a lot of wiring diagrams and circuit diagrams help books and stuff like this at reliable-store
the girl in the chat box can help u instantly... im a frequent buyer there since Im a mechanic so take help from there
1/26/2019 10:17:30 AM •
2008 Hummer H3
•
Answered
on Jan 26, 2019
•
181 views
Traction failed error, can't shift
To cancel the error of not starting,removing the battery terminals both positive and negative put them together for ten minutes ten reconnect and start and the ecm will have rebooted itself
8/6/2016 8:59:54 PM •
2008 Hummer H3
•
Answered
on Aug 06, 2016
•
222 views
My hummer h3 2008,the oil pressure lindicator
The engine will shut down to protect itself,check the oil level and see whether the car has oil.The light comes on if the oil level is low or the oil pump is not pumping any oil.I replaced my engine hummer h3 two weeks ago due to a malfunctioning oil pump.Check if you oil pump is not malfunctioning.Good luck hope you have not damaged anything further like the bearings due to lack of oil.
8/6/2016 8:14:56 PM •
2008 Hummer H3
•
Answered
on Aug 06, 2016
•
1,799 views
The Power will not turn on.
Pam Jeffers... hello,
Then look to your grounds (frame, engine & body)...
The problem with a GLOBAL phrase like "will not turn on"
indicates (
very unlikely) everything...
Nevertheless
I always recommend for flawless documentation... get the
FACTORY+WORKSHOP+MANUAL... & H3+2008...
Barring that research & purchase check "bbb industries"
(below) for your vehicle...
Also check what your OBD (on board diagnostic) is telling you about registered fault codes
BBB Industries Premium Alternators Starters Power Steering Products
5/17/2016 8:30:55 PM •
2008 Hummer H3
•
Answered
on May 17, 2016
•
358 views
Not finding what you are looking for?