2008 Buick Enclave - Answered Questions & Fixed issues
Where is the turn signal flasher on the 2008 Buick enclave
More than likely the problem in in the turn signal switch and not the flasher. But first, make sure that the bulbs are good. One bad one will keep the other from working, Using the emergency flasher, see if they are all working.
10/1/2022 10:03:33 PM •
2008 Buick...
•
Answered
on Oct 01, 2022
•
389 views
2008 buick enclave fuel filter location?
I recently tried the DIY service and repair manuals
from a website and it actually helped me repair transmission problem in my jcb 3cx site-master. It would'nt move forward or reverse, engine was good both solenoids for forward and reverse worked, but still couldn't diagnose the problem.
I don't have much technical knowledge but I just followed it step-wise, and now it works perfect! covers wiring, codes, diagrams, torque specs, PCV, everything
got it from
www.reliable-store.com
8/15/2021 2:00:06 AM •
2008 Buick...
•
Answered
on Aug 15, 2021
•
2,287 views
How do you remove buick enclave headlight assembly
If you just have replaced the bulb, no need to remove the assembly. However, if the headlight needs to be removed, it is possible.
• Installing a bulb: Remove the wheel behind the headlight in question, now you would have room to change the bulb without removing headlight
• Removing the assembly: Remove the Facia and the bumper, and you can now easily remove the headlight.
4/29/2020 12:01:33 AM •
2008 Buick...
•
Answered
on Apr 29, 2020
•
9,601 views
2008 Buick Enclave; front passenger, no power to
Do you know anything about automotive electronic's ? Serial data Communication network ? Electronic module's inside the vehicle doors , communicate commands ! No relay ,no fuse .
If the passenger mirror is selected and a direction switch is activated, the DDM sends a serial data message to the PDS indicating that the passenger mirror was selected and the direction to be commanded. The PDS will then supply battery voltage and ground to the appropriate control circuits for the direction selected.
DDM - driver's door module
Door Lock System Components
The power door lock system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Door lock relay--Located in the instrument panel (I/P) fuse block and controls the locking of the rear doors.
• Door unlock relay--Located in the I/P fuse block and controls the unlocking of the rear doors
• Body control module (BCM)
• IP BEC
• Reversible door lock actuators in each door
Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Body control module (BCM)
• Passenger door module (PDM)
• Rear door power window switches
• Power window motors in each of the doors (circuit breaker protected)
Your best bet , take it to a qualified repair shop that has a diagnostic scanner that can pull code's an view input data form these systems . There is one circuit breaker for the window's an fuse's for the lock's . I would think a data network problem . But that would be a guess , without testing anything is possible on these .
12/27/2017 4:14:35 PM •
2008 Buick...
•
Answered
on Dec 27, 2017
•
3,183 views
Trailer running lights
First fix the shorted trailer lights, then check the owner's manual all fuse info is in the manual. If you don't have the owner's manual go to the GM owners website and download a free one there in pdf format.
7/26/2017 9:44:18 PM •
2008 Buick...
•
Answered
on Jul 26, 2017
•
159 views
Where do I find the
2008 Buick Enclave neutral safety switch
It's called a Manual Shift Detent (w/Shaft Position Switch) Lever Assembly. And it's inside the transmission .
What problem are you having ? No crank , when you turn the ignition switch to the start position nothing happens ? No click ,nothing ? If your think of just replacing the switch ,stop , did you have it diagnosed ? This starting system is computer controlled .
When the ignition switch is placed in the Start position, a discrete signal is supplied to the body control module (BCM) notifying it that the ignition is in the Start position. The BCM then sends a message to the engine control module (ECM) notifying it that CRANK has been requested. The ECM verifies that the transmission is in Park or Neutral. If it is, the ECM then supplies 12 volts to the control circuit of the crank relay. When this occurs, battery positive voltage is supplied through the switch side of the crank relay to the S terminal of the starter solenoid.
DTC P0615: Starter Relay Control Circuit
have the vehicle checked .
6/20/2017 5:16:11 PM •
2008 Buick...
•
Answered
on Jun 20, 2017
•
1,832 views
08 Buick Enclave alarms randomly
well if it telling u "hood open" and hood is closed then that circuit is acting up find switch test it also check wires for lose broken eaten barewires
5/15/2017 8:10:22 PM •
2008 Buick...
•
Answered
on May 15, 2017
•
594 views
2008 Buick Enclave The sound comes on and off when it wants. The sound for music, blinkers and back up alarms do this, although the stereo looks like it working just fine. What's the problem?
Saying this or that is the problem won't work with your vehicle , an most all vehicle's . Given the amount of electronic's (computers C.A.N communication networks etc.. ) The BCM - body control module uses input's from ignition switch signals to determine what mode the vehicle is in . The BCM energizes relay's an sends messages on the serial data network to wake up other modules . The radio is also on the C.A.N network , signals from the BCM could be turning it on , as well as the turn signals , because the BCM functions the turn signals too .
The LT/TRN/SIG and RT/TRN/SIG fuses in the I/P fuse block supplies battery positive voltage to the body control module (BCM). When the turn signal switch is placed in either the left or right position, a signal is sent to the BCM to illuminate the desired turn signal lamps. The BCM has an internal flasher that sends an ON-OFF voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, a separate ground signal is sent to the BCM to activate and flash all turn signal lamps including both IPC turn indicators. The front and rear turn signals are grounded at G401.
How to Diagnose Controller Area Network CAN
This is something best left to a qualified repair that has the proper tools to diagnose it .
3/3/2017 10:31:22 PM •
2008 Buick...
•
Answered
on Mar 03, 2017
•
722 views
Not finding what you are looking for?