2008 Dodge Nitro - Answered Questions & Fixed issues

If both the coolant hoses are hot then the coolant is passing through the heater core. You probably have an actuator or blend door that is not working. It may be restricted by commanding it to work. A scanner could help you find out the problem.

You have two fans, one to cool the radiator, and one to heat the cabin. https://www.google.com/search?q=2008+Dodge+Nitro.+How+to+remove+grey+plug+for+resistor+in+fan+shroud ..

WHAT GETS WARM, ? (OUTSIDE HERE IS 80F) ENGINE IS 200F,? IS DASH HEATER WARM? IS DASH CLUSTER ******* OUT ENGINE TEMP? MY GUESS FAILURE TO CRANK! AND BATTERY LUGS ARE LOOSE AND OR RUSTY. WON'T CRANK? OR CRANKS FAST AND WILL NOT START. IF STARTER IS DEAD CRANK IN NEUTRAL NEXT, NOT PARK. SEE IT CRANK NOW? YES PRNDL SWITCH IS BAD. AND START IS THE IMMO LAMP GLOWING WRONG IN DASH "SECURITY" IF NOT HAVE THE CAR JUMPER CABLE STARTED AND NEVER DO THAT WITH CABLES BACKWARDS OR GO BROKE FAST.

Did you check the head for leaks? If you tested the head then it can only be the gasket or lack of a good seal that can be causing the leak. There's no direct route to the exhaust for the coolant except when there is damage or something not installed correctly. Did you torque the cylinder head using the correct sequence? The correct pressure applied through following the sequence is what causes the gasket to seal properly. Uneven tightening or re-using old bolts when they are not supposed to be used can cause issues as well. Torque to yield head bolts are never to be re-used because they stretch when installing them. Was the surface spotlessly clean before attempting to install the gasket? You can only re-start the process and make sure everything is done correctly. Good luck.

Question edited for clarity and spelling 'worm' to 'warm'. Question moved to Model category. Larry gives the perfect answer as always.

• ALL FUSES test good, and IMMO lamp reads good? no engine told at all and is and engine problem. and has gas or diesel engine, omg not the same at all warm not WORMs, rats eat wires but not worms, LoL. this failure is called in tech/engineers world as HOT SOAK FAILURE, most times spark dead. that stator always works right the cars starter motor cranks load and fast we all that robust cranking even does 300 rpm . so is not a start run problem it is a dead silent starter the only clue to me is the jumper wire, wow. The PCM controls 3 relays ASD relay and Starter and fuel pump relays. so if really did hot wire real starter relay them means the PNRDL is bad. got automatic transmission.???? got what engine. \USA car, sorry cant guess cars, drivelines ever. do you have the security system OEM on this car and the IP cluster lamp same name is NOT HAPPY as the users manual tell you. got both keys to Ignition car new provide or lost one if both try them both? guess #2 automatic trans does the starter motor spin in P and N both must work and P fails long before P so we try both . the starter relays is controlled by 1 computers, not just one and the PRNDL switch. I have the schematic here. PRNDL shows what gear it is , wrong selection is made the PRNLD tells first the PCM, and if PCM is happy the PCM click (energizes) the Starter relay the MTIP module contains the relay and can fail too. if the IMMO fails , it may not crank. or can cuts spark. if the starter does work the ASD can cut fuel if the PCM sees any kinds kinds of bad spark. spark coils dead, CMP dead CKP dead to prevent fires. it cuts fuel dead. so does IMMO./ if you scan the PCM it tells you why it cuts those relays. if you had done that.
• Larry Ng Sep 02, 2022 learn to check all fuse first then scan it and if the starter motor fails say it will not crank or the starter motor is silent.

More here https://www.google.com/search?q=2008+Dodge+Nitro+problem+starting+when+engine+warm ..

I am not familiar with the model but changing a flexplate is neither quick or easy as either the transmission or the engine must be removed and with some vehicles the power unit must be completely removed and separated on the bench.

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything someone on fixya recommended it to me and I thank him even today They have full manuals and it's verrrrry cheap and mine I got free in offers 3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins there is one website more but i don't remember its name it was 2 years back bitman something link this Try these out brother

inside the tank

replace the relay

Possible failing fuel pump. Check the fuel pressure when it acts up.

You can get all wiring diagrams, torque specs, electrical diagrams, controls etc. at www.reliable-store.com Best place

Look at youtube Knock sensor location on Dodge grand Caravan 3.6

Open the front doors and look on the sides of the dash for a pop off panel

usualy on the block.or in the eng v for v8,s

maplins or any diy electrics store will have them in stock even vehicle spare shop will have the fuse.

Circuit for the horn button in the steering wheel goes through the clockspring, which also has wiring for the drivers air bag, cruise control operation (if equipped), and radio controls (if equipped). The clockspring unit can be replaced, but BE SURE to disconnect the negative battery cable and wait for an hour before trying to remove it so you don't inadvertently set off the driver's air bag.

Mine was on because I forgot to turn my handbrake off and I was driving

Hello Cam Nicholson, Can't.... Isn't broke... I Normally for a luxury car I might be tempted to consult the OWNERS MANUAL to see if the lights have indeed go on to the absurd... or even inane (perhaps insane)... But a dear friend has a Nitro... I know better...! Answer = No (Fix? Check out those $$$$ new cars) Contemplate for a moment where the fluid is stored... Go there... (like the rest of us...) if it is low... PUT SOME IN... (same as my Lincoln) Frankly I'm having trouble trying to believe there is a Nitro Light for washer fluid ... (see "LID" below) Hope this helps... Carnac the Magnificent http://www.rockauto.com/en/catalog/dodge,2008,nitro,3.7l+v6,1441403,wiper+&+washer,windshield+washer+fluid+reservoir+cap,11097 More Information for MOPAR 68020727AA

Have a look on the following link (but notice that it is a right hand drive vehicle in the photo): OBD2 connector location Dodge Nitro 2006 RHD The OBD2 port is usually 'within an arm's reach' of the steering wheel.