20 Most Recent 2008 Chevrolet Equinox Questions & Answers


You first want to look to see the status of the code. Is the code current, pending, or permanent? If pending, you will want to clear the code and see if it comes back, same thing with current. If the code is permanent then you would want to start by visually inspecting the wiring harness at the transfer case and the transfer case control module. If there are no visual defects found then you will need to complete a diagnostic procedure to determine if it is the module or the wiring. I would be happy to walk you through this process. Please feel free to contact me at:

https://www.6ya.com/eugene_aa01c1a9fa4c2ed9

2008 Chevrolet... | Answered on Mar 15, 2019


This lo beam description, hope you can read it. You have hi and lo beam fuses, on lo beam use test light on the lo beam fuse, any voltage? The voltage comes from lo beam relay. Voltage and ground are important.
low beam system-otildwcdblznnvvsmhostjd3-3-0.jpg

2008 Chevrolet... | Answered on Feb 16, 2019


I got a 2007 Chevy equinox I need to know how to change a thermostat and it has some weird thing on the top got the bolts out but I can't get the thermostat


2008 Chevrolet... | Answered on Jan 27, 2019


From the factory you had orange Dexicool. If you have drained the system, I would suggest filling it with the yellow universal. If you are just adding a little, use the orange.

2008 Chevrolet... | Answered on Oct 04, 2018


Very common and due to rust. Soak it with WD40 and let stand overnight and then use a large blunt object to knock it loose.

2008 Chevrolet... | Answered on Jan 04, 2018


Your best bet ,take it to a qualified repair shop that has the diagnostic test equipment to find the problem .

2008 Chevrolet... | Answered on Nov 12, 2017


firstly - your symptoms are not directly associated to any brake "failure". The noise is likely related to either a faulty sensor for the abs, the signal/information going to the abs controler is incorrect (not your basic brake function. If your ABS light comes on it is just telling you that the ABS system has been switched off. ABS is there for emergency situations. Your can still has brake function like you had befoore ABS was introduced. You have no need to be concerned as emergency stopping with normal brakes about town would rarely engage ABS. Your dealer "interogates" the ABS controler for fault reports. However, the fault needs to be apparent for this fault report to work. keepit until the ABS light comes on. WITHOUT switching the engine off take it straight to your dealer. switching of may dumpt the fault report so DON'T. Hope this helps.

2008 Chevrolet... | Answered on Oct 29, 2017


Assuming that you feel and hear the engine smoothly accelerating while the stutter occurs, you are probably looking at transmission. Torque converter? possibly. A full diagnostic of the transmission is certainly in order as there are a number of things that might cause that condition.

2008 Chevrolet... | Answered on Oct 22, 2017


Take to a qualified repair shop an have the vehicle checked for DTC'S - diagnostic trouble code ! Do you know what DTC'S are .

2008 Chevrolet... | Answered on Oct 20, 2017


Try a window ,see if they still work too . RAP relay supply's power for radio windows etc. when key is turned off for ten mins or till a door is open .

2008 Chevrolet... | Answered on Jul 24, 2017


Fuel, compression and spark.

Check the above. If you have adequate fuel pressure, reasonable compression and a good spark the engine should start. It may also be a good idea to check for compatibility with your engine control module between a 2008 model year and the 2005 model years.

2008 Chevrolet... | Answered on Jul 23, 2017


c0040 right front abs sensor.
P0300 random or multiple misfire.
p0303 cylinder 3 misfire
this code P0300 and this one p0303 will be the same problem as they both same coding.
C0040 it can be the cable is cut or the sensor is defective.

2008 Chevrolet... | Answered on Jul 19, 2017


I had the same problem with my radio. I replaced the 15 amp fuse. Located in passenger side fuse box. For some reason it wasn't blown, but worked when I put a new one in.

2008 Chevrolet... | Answered on Jun 07, 2017


Mass air flow sensor maybe ! Be nice to know what data sensor parameters are . Do you know what these are ? Your vehicle has a number of sensors that supply the engine computer with data ,signals what ever you call it ! Do won't to get to technical on you . Your engine has crank sensor , cam sensors , coolant temp sensors , intake air temp . sensor , manifold pressure sensor , throttle position sensor etc.... They have a voltage coming from the PCM/ECM - engine computer , an they send another voltage back to the computer . With progamming inside the computer it knows from these voltage signals what the temp. of the engine is etc.... With a proper scan tool you can see what the computer inputs are . Even a bad coolant temp sensor could cause the problem your having .

2008 Chevrolet... | Answered on Apr 20, 2017


There are three relays for the cooling fan's , two of them . And all three are located in the under fuse/relay box. Watch this training video on how they work an how to test them. Relay Driven Dual Cooling Fan Diagnostics

2008 Chevrolet... | Answered on Apr 14, 2017

Not finding what you are looking for?
Cars & Trucks Logo

709 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Jonah Oneal

Level 3 Expert

14061 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Equinox Chevrolet

  • Equinox Chevrolet

Most Popular Question

2008 awd equinox service awd light but

  • Cars & Trucks
Loading...