20 Most Recent 2007 Chevrolet Silverado 1500 2WD Questions & Answers


Excessive Fix a flat in tire,,, bent rim,,, bent drive shaft,, or bad u joint,,

2007 Chevrolet... | Answered on Jul 24, 2019


Vent solenoid is located by the fuel tank fill hose mounted to the box.

2007 Chevrolet... | Answered on Jul 21, 2019


Yes it will cause the check engine light to come on if it is not tightened.

2007 Chevrolet... | Answered on Jul 21, 2019


Replace pump up lifters,, or install Active fuel management delete kit,,best bet

2007 Chevrolet... | Answered on Jul 21, 2019


I, feel sorry for you, after reading your problem, but don't worry you visit the Reliable-Store they will help you for sure.
Best Manuals

2007 Chevrolet... | Answered on Jul 21, 2019


Chevy dealer says will not come on until temperature reaches 219 f

2007 Chevrolet... | Answered on May 14, 2019


sadly NO we can not .

2007 Chevrolet... | Answered on Feb 05, 2018


Even though you have a manual HVAC system it still has the capability to set an store DTC'S - diagnostic trouble code's .
DTC B0413 02: Temperature Control 1 Feedback Circuit Short to Ground (CJ3)
DTC B0413 05: Temperature Control 1 Feedback Circuit Short to Battery or Open (CJ3)
DTC B0413 61: Temperature Control 1 Feedback Circuit Actuator Stuck Open (CJ3)
DTC B0423 02: Temperature Control 2 Feedback Circuit Short to Ground (CJ3+C67)
DTC B0423 05: Temperature Control 2 Feedback Circuit Short to Battery or Open (CJ3+C67)
DTC B0423 61: Temperature Control 2 Circuit Actuator Stuck (CJ3+C67)

Did you have Actuator Recalibration done after replacing the actuator or control module ?
Your best bet ,take your vehicle to a qualified repair shop .
Preferred Method (w/ Scan Tool)
Clear all DTCs.
Place the ignition switch in the OFF position.
Install the HVAC actuator.
Connect all previously disconnected components.
Start the vehicle.
With the scan tool, initiate the Motor Re-calibration feature of the Heating and Air Conditioning Special Functions menu.
Verify that no DTCs have set as current DTCs.

2007 Chevrolet... | Answered on Dec 23, 2017


Sounds like it might be a damaged rear end. Chock the wheels or put rear differential on jack stands and put vehicle in neutral then by hand turn the drive line back and forth and see if there is any loud noise when u do. There should not be a lot of play. if on jack stand you can also turn one of the rear wheels and see if there is any load noises or excessive play

2007 Chevrolet... | Answered on Dec 17, 2017


go to the wreckers and get a replacement fuse holder and wiring harness quicker and easier than trying to replace the fuse holder of the damaged wires

2007 Chevrolet... | Answered on Dec 14, 2017


Time for a rebuild

2007 Chevrolet... | Answered on Nov 12, 2017


Take battery cable off for 5 mins, then put battery cable back on. Insert your key into the ignition turn to on but don't start the vehicle wait 5 seconds turn back off repeat the key on/off three times. This initiates a re calibration of climate control equipment and actuators. It will fix your problem.

2007 Chevrolet... | Answered on Nov 06, 2017


I had the same problem! I used a piece of wood to keep the break pedal depressed and then started to remove one of the break lamps and to my surprise it came on! Same thing on the other side. So I did not seat (bottom out) the lamps in their sockets and both break light are now working properly. I had a similar issue last spring but that time only one light was out. I put in a new bulb and it still did not work so I messed around with it a little more and it started working. Never did figure it out until now. Hope this helps!

2007 Chevrolet... | Answered on Apr 02, 2017


Here you can look it up , may like to have this for future reference ! http://bbbind.com/free_tsb.html free wiring diagrams an fuse box diagrams as well . When you click on this blue link I copied , click on wiring diagrams , not TSB'S ! You may want to check them out later ! TSB'S are technical service bulletins .Well ant way ,after you click on wiring diagrams enter your vehicle info. , year , make , model , engine size . Then under system click on electrical distribution , under subsystem click on fuse panel .Then click search . Two blue links will show , click one at a time till you find what your looking for .

2007 Chevrolet... | Answered on Oct 08, 2016


code p 0700 refers to transmission control system/MIL---malfunction==== causes --TCM---wiring
check all connections and wiring condition or replace the TCM
code p 0717 refers to turbine shaft speed (TSS) sensor ---no signal====causes ---wiring---TSS sensor---ECM/TCM
logically the TSS reports to the TCM to facilitate ratio changes so if the wiring , connections etc are not good then one will affect the other
Take it to an accredited auto transmission specialist shop, have it properly diagnosed and a quote
do not confuse a TSS with a VSS sensor as they are two different speed sensors in the same box

2007 Chevrolet... | Answered on Sep 23, 2016


The body control module (BCM) could be defective but the sockets and associated wiring could be at fault as well.

2007 Chevrolet... | Answered on Sep 10, 2016


Undo your negative cable for 30 seconds ,,it may reset itself,,,

2007 Chevrolet... | Answered on Aug 05, 2016

Not finding what you are looking for?
Cars & Trucks Logo

463 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Silverado 1500 Chevrolet

  • Silverado 1500 Chevrolet

Most Popular Question

need remove fuse box get wire harness

  • Cars & Trucks
Loading...