20 Most Recent
2007 Dodge Ram Truck - Page 8 Questions & Answers
2007 dodge ram 4.4 beeps when i press the brake
If you have a beebing noise every time you press on the brake, it is because a tail light is burnt out. There are two filaments in each brake light. Therefore, when you turn on your hazards, it will appear that both tail lights work properly. The beebing warning sound is actually a feature that Dodge put in the Rams so drivers would know their tale light is out. Just replace the tail light bulb, and the beebing will automatically cease. To get the tail light housing out, you will need a torex screw driver. Also, you twist the bulb housing out as opposed to pulling it out. There are three prongs that twist out.
My 2007 Dodge ram 1500 with hemi has 2 codes po524 and po406 are they related
In both cases, there is a software update available for this condition. It involves
having the dealer connector their StarScan tool to your truck and
reprogramming the PCM.DTC P0406 - EGR Sensor "A" circuit "High"There is updated software available for your PCM that will correct this
code if your vehicle was built prior to mid February 07. If it was built
after that, then the EGR valve will need replacing (this is not unusual). Keep in mind that could be time for a new valve, but you dont will need to change the tube, but new gaskets are a good idea.DTC P0524 - Oil Pressure Too Low Oil pressure sending unit (sensor) voltage input above the maximum acceptaple voltage.
If the software is up to date, then have the oil pressure sensing unit must be replaced.
Additionally, check this TSB SUPERSEDES TECHNICAL SERVICE BULLETIN 18-044-07, DATED OCTOBER 12, 2007, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALLREVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE THE ADDITION OF YEARS, MODELS AND CLEAN DATES.THE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.StarSCAN SOFTWARE LEVEL MUST BE AT RELEASE 8.04 OR HIGHER FOR THIS BULLETIN.StarMOBILE STANDALONE MODE OR StarMOBILE DESKTOP CLIENT MAY ALSO BE USED TO PERFORM THIS PROCEDURE.SUBJECT:Flash: MIL Illumination Due To Diagnostic Trouble Code P0524 - Engine Oil Pressure Too LowOVERVIEW:This bulletin involves selectively erasing and reprogramming the Powertrain ControlModule (PCM) with new software.MODELS:**2007** - 2008 (DR/DH/DC/D1) Ram Truck (1500/2500/3500)**2007** - 2008 (HB / HG) Durango / Aspen**2007** - 2008 (LX) 300 / Magnum / Charger**2007 (LE) 300C/300 Touring (International Markets)****2007 (L2) 300 (China)****2007** - 2008 (WK) Grand Cherokee**2007 - 2008 (WH) Grand Cherokee (International Markets)****2007** - 2008 (XK) Commander**2007 - 2008 (XH) Commander (International Markets)**NUMBER: 18-003-08GROUP: Vehicle PerformanceDATE: January 19, 2008NOTE: This bulletin applies to the above listed vehicles equipped with a 5.7L engine with MDS (sales code EZB) built before the following dates:(HB/HG) built before August 15, 2007 (MDH 0814XX)(LX) built before September 14, 2007 (MDH 0914XX)(DR) built before August 16, 2007 (MDH 0816XX)**(WK/WH/XK/XH) built before January 8, 2008 (MDH 0108XX)**SYMPTOM/CONDITION:The vehicle operator may experience a Malfunction Indicator Lamp (MIL) illumination due to the following Diagnostic Trouble Code (DTC): P0524 - Engine Oil Pressure Too LowHope this helps; also keep in mind that your feedback
is important and
I`ll appreciate your time and consideration if you leave some
testimonial comment about this answer.Thank you for using FixYa, have a nice day
2007 dodge ram 5.7L cant get the fault codes
Hi!!
AutoZone and other autopart stores will scan the trouble codes and give you a print out with the TC number and their meaning. This is a free service they offer to their customers.
Don't forget to rate this post. Good Luck!!!
Dodge ram won't start and ECM light and check
First you need to retrieve the trouble codes stored in the computer.If you don't have a code reader or scan tool you can take it to your local autoparts store (advance auto,autozone,ect) and they can retrieve them for you.Then we can go from there.
Blower motor not working
Check the connection at the blower motor resistor.Turn the ignition and fan switches on and wiggle the connection or pigtail.Or it could be a faulty blower motor resistor.Usally these connection get hot and loose there connection.
WHAT DOES PO 524 MEAN IN THE TROUBLE CODES THAT POP UP
It indicates low oil pressure.There is a technical service bulletin on this problem and you will need to take it to your dealership and have power train control module reprogramed with the new software to fix this problem.There should be no charge for this.
97 Dodge 2500 wiper fuse
this sound like the wiper motor auto wiper parking is shorting out and so with ign turned on this causing fuse to blow ? if motor has a short wire to earth on exterior ? usually brown ? this is auto park cut or disconnect then ensure you have correct amp fuse and see if fuse blows? if yes then provided the elec plug connector for motor is in good condition ? may well be motor has a fault on armature to earth? hope this helps
PO524 WHAT DOES IT MEAN
Hi John,Diagnostic Trouble Code (DTC) P0524 has a generic description of "Oil Pressure Too Low."There are SEVERAL things to consider here:First: Your engine is VERY sensitive to oil viscosity. Since it came up right after an oil change, I would question whether the correct viscosity oil was used. Also, if there has been any aftermarket fluids/chemicals added to the engine oil (like those that make claims to clean your crank case) this can have an adverse affect on oil viscosity.Second, The actual oil pressure should be checked with a manual gauge to verify proper oil pressure sending unit operation and to see if a low oil pressure condition actually exists.Finally, If everything is OK in the items listed above, there is a Technical Service Bulletin (TSB) published for your truck that has to do with "false" code P0542. It requires an update of your computer software to correct it. The TSB Number is 18-003-08.If your truck requires the software update, it can be done at the dealership for free if your vehicle is still covered under the 8-year/80,000 mile emissions warranty. (It should be covered unless you have more than 80,000 miles)
Not finding what you are looking for?