20 Most Recent 2007 GMC Envoy Denali Questions & Answers


Should on the inside of the frame underneath the vehicle

2007 GMC Envoy... | Answered on Feb 09, 2018


There is a recall for the master switch, call the dealer and give them your VIN #.

2007 GMC Envoy... | Answered on May 26, 2017


Door open chime? Mayhem defective door switch

2007 GMC Envoy... | Answered on May 13, 2017


Could be crank or cam sensor

2007 GMC Envoy... | Answered on Mar 12, 2017


The switch goes bad with time. Replace it.

2007 GMC Envoy... | Answered on Aug 03, 2016


There is a level sensor connected to the lower control arm on the rear wheel on the drivers side. This operates the pump and lets air out if it is too high in the back.It can fail. Most likely the air pump has gone bad. Expect 800 + to fix it.

2007 GMC Envoy... | Answered on Jul 24, 2016


Depends on where it is located. If its on the drive shaft for the rear wheels the cost will be lower than the ones on the front wheels. Shop around. Drive line shops specialize in them but any good mechanic can do it.

2007 GMC Envoy... | Answered on Jul 24, 2016


Run a diagnostic test to show what codes come up. That will identify the reason the engine light came on. It will also reset the light.

2007 GMC Envoy... | Answered on Jul 24, 2016


Check the light switch, fuse, relay and the wiring to the bulbs. Don't forget the ground wires either.

2007 GMC Envoy... | Answered on Jul 24, 2016


Fuel sender is in the gas tank. You'll need to let the tank down in order to replace the sender.

2007 GMC Envoy... | Answered on Jul 23, 2016


Relay is stuck or the head light switch itself is bad

2007 GMC Envoy... | Answered on Jul 23, 2016


Evap Emission High Purge Flow Fault. This means that the carbon cannister under the hood that collects fuel tank vapors is no longer operating. You won't pass smog until it's fixed.

2007 GMC Envoy... | Answered on Jul 23, 2016


Usually Kurt there will be a bracket on the tube that secures it to the engine block. Undo the fastener that secures the tube and gently pull upwards while rotating the tube out of it's press fitting. To install a new tube or when replacing the old one...select a box wrench that is just a little bigger than the tube diameter and slide it down to the bottom of the tube until it is pressing against the seating flange. Make sure the alignment of the bracket is close to where you want it to be and then gently tap on the edge of the box wrench to seat the tube. A long handled screw driver helps in tight quarters. Secure with fastener.

2007 GMC Envoy... | Answered on May 04, 2016


The T PARK fuse in the rear fuse-relay block supplies battery positive voltage to a separate park lamp circuit connected to the trailer wiring harness..
For trailer wiring, separate turn signal circuits are connected through the GMSF to the trailer wiring harness.
Fuse Block - Rear
Beneath the left rear seat
Trailer TR/PARK fuse 42 10amp

2007 GMC Envoy... | Answered on Apr 14, 2016

Not finding what you are looking for?
2007 GMC Envoy Denali Logo

250 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 GMC Envoy
2004 GMC Envoy

2,174 Questions

2002 GMC Envoy
2002 GMC Envoy

1,364 Questions

2003 GMC Envoy
2003 GMC Envoy

1,327 Questions

2006 GMC Envoy
2006 GMC Envoy

569 Questions

2005 GMC Envoy
2005 GMC Envoy

521 Questions

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Envoy GMC

  • Envoy GMC

Most Popular Question

gmc envoy 2007 denali low light stopped

  • Cars & Trucks
Loading...