20 Most Recent 2007 Cadillac SRX - Page 6 Questions & Answers

you may want to check your AC drain it may be clogged allowing water to back up and leak in to vehicle

In order to get at the lamps you need to remove the front bumper skin, I have found that it is easier to take it to the dealer to do. It will cost you about one hours labor.

change it.

Best thing to do is take it in for a 4 wheel alignment. There is always a chance that a part is wearing out, or has been bent.

Any body shop has a great big book with those pics in it. Say pretty please.

Probably something else. These are connected via wiring from them down the inside of the steering column to a connector at the bottom. There will probably be a problem at the connector or in the wiring in the column or from the connector on to the BCM.

i have a Cadillac srx, my 3rd row is now coming up can you help me. i tried the buttons, they make a beeping noise but the seat doesn't come up

Most likely the main fuse may be blown, usually located in from fuse box. but i suggest you check

What year is it ? replace front turn signal ??? You mean the bulb . You may need to remove the headlamp assemble an the bumper cover .

service Stabilitrak light on Take an have DTC'S - diagnostic trouble codes checked , Dealer

Most times when that happens it could be a mechanical blockage. In the tool kit that came with the car there should be a hex tool to manually close the roof. There should be an access panel at the front with a pop off cover. If you remove that cover there should be a female hex that the tool fits into to manually close the roof. If you have the female hex on the sunroof but no tool, most times the correct size allen/hex wrench will do in a pinch. Try opening the sunroof fully with the tool and verify there is nothing in the rails or lead screws the will keep it from closing fully. Also check for a blown fuse to the sunroof.

Door ajar switch possibly . The lift gate not working is a different matter . Could be any number of thing's . Power Liftgate System Components • Liftgate motor assembly • Liftgate latch • Liftgate module (LGM) • Liftgate side upper sensor - left • Liftgate side upper sensor - right • Liftgate handle switch • Liftgate close switch • GMLAN serial data link • PWR LIFT GATE 30 amp fuse • PLG 10 amp mini-fuse Your best bet take it to a qualified repair shop that has the diagnostic tool that can communicate with the lift gate control module , too check for DTC'S - diagnostic trouble code's . Liftgate Module The liftgate module controls the liftgate motor, liftgate clutch, and liftgate latch based on various inputs. The liftgate module also performs diagnostics on these inputs and outputs and will disable liftgate functionality and set DTCs should a fault be detected. The liftgate module is secured to the motor assembly at the left rear of the vehicle. The module requires a liftgate position learn procedure be performed when replacing. This allows the module to learn the full open and full closed positions of the liftgate. DTC B153A 00: Liftgate Latch Switch Signal Circuit DTC B153A 08: Liftgate Latch Switch Signal Circuit Signal Invalid DTC B153B 02: Liftgate Open Switch Signal Circuit Short to Ground DTC B153B 05: Liftgate Open Switch Signal Circuit Open DTC B153E 02: Liftgate Position Sensor Signal Circuit Short to Ground DTC B153E 05: Liftgate Position Sensor Signal Circuit Short to Battery or Open DTC B153E 08: Liftgate Position Sensor Signal Circuit Signal Invalid This is not a job for a diy'er or vehicle owner .

it sounds like the dvd unit has gone faulty

The EVAP purge valve is connected to the EVAP canister and is located at the rear of the vehicle.

Make sure cable connection are clean baking soda & vinegar

Ask to see the area of concern if they won't show you pay your bill and fill the oil up and take it some where else.

The fact you say that disconnecting and resetting the computer tells me the following:: This sounds like it is going into "Limp mode" a mode the computer puts the vehicle into when it detects something is wrong , or sometime is programed to do this when the vehicle is way overdue for its service, I would suggest that you take it to a reputable dealer and ask them to read the computer to see what fualt codes are showing , this should help solve the mystery or at least point you in the right direction. The onboard computer is forcing the vehicle into the "Limp Mode" your dealer yould know this and should have checked the onboard computer first

You have a BIG problem and need it resolved from dealer if still under warranty. If no help , ring head office.

Audio Amplifier In left rear quarter panel behind trim panel