2012 Cadillac SRX Premium Collection - Page 5 - Answered Questions & Fixed issues

Rear hatch ??? power liftgate or just won't unlock ? Power Liftgate System Components The power liftgate system includes the following components: • Liftgate motor assembly • Liftgate latch • Liftgate module • Liftgate side upper sensor - left • Liftgate side upper sensor - right • Liftgate handle switch • Liftgate close switch Did you check for DTC'S - diagnostic trouble codes in the liftgate control module ? do you know what I'm talking about ?

its wired up wrong, must be aftermarket radio hack job; the cad as fuse marked radio this fuse feed works.so use that. just like the factory radio did.

not told country, USA , if you have 2 good keys can make 6more. not in canada. not told at all; country must be learn ESP>? is this a door lock problem only?????????

1. immo failing and spark is dead, for this.? engine dead.
2. got 2 good keys. yes /no USA yes if 2 good.
3. NO, then a lock smith can do it (some ) call em.????yp.com
4. or the dealer sure.

the exact full rules very by country this forum does above equator cars. even UK. you speak English are you in india? welcome to the www, world wide web where anyone can post;

You will need to refer to the Cadillac service manual for the exact sequence and specs. Generally, the torque specifications for the bolts range from 8-11 ft-lbs and should be tightened in the following order: (1) center bolts, (2) outer bolts, (3) inner bolts, (4) lower bolts.

My guess is Body Control Module comm failure, which would explain inoperative windows and door locks. Lighting is likely non operational also?

Check any/all fuses labeled BCM. You could also try disconnecting battery for few minutes and see if problem clears.

fit the TCM and use a scan tool to reset the unit

You can't. Fix the problem not find a way around it. Have a read https://www.fixya.com/cars/r29887709-gm_passlock_security_system ..

I think on this model it is a pain in the tailbone to remove it. At the pedal end the connector is held in with 2 tiny pegs that you will need to carefully press out of the way with two small, flat bladed screwdrivers.This is one of those jobs that will either release first time or take all day and the skin off your knuckles. It will also involve a lot of cursing and swearing at the vehicle.

Which engine is fitted to your Cadillac? As a general rule Cylinder One is usually positioned nearest the belts and pulleys on the end of the engine, the furthest away from the transmission. Stand in front of the engine with the belts and pulleys nearest to you. The cylinders to the LEFT are the Odd numbers, (1,3,5,7), and the cylinders to the RIGHT are the Even numbers, (2,4,6,8). Number One is LEFT side nearest to you.

Fuel can go bad after sitting for a long time...fuel pumps sometime will also get rusted with the bad fuel...try using starter fluid and see what it does.

it appears that 4 are sold as package and suggests that placement does not matter.

Most likely the gaskets need to be replaced... maybe the valve cover, oil pan, etc...if oil gets on the exhaust it can cause the oil to smell

That depends on whether you have Passkey I or Passkey II See this post for instructions https://ricksfreeautorepairadvice.com/passkey-versus-passlock/

To replace the freeze valve in a 1998 Cadillac DeVille, you will need to follow these steps:

1. Locate the freeze valve. It is typically located near the radiator or the heater core, and it is responsible for preventing the cooling system from freezing in cold weather.
2. Disconnect the negative battery cable. This will prevent any electrical accidents while you are working on the car.
3. Drain the cooling system. This will allow you to remove the freeze valve without spilling coolant all over the engine compartment. To drain the cooling system, locate the drain valve at the bottom of the radiator and open it.
4. Remove the freeze valve from the cooling system. This will typically involve loosening the mounting bolts or screws that hold it in place, and then pulling it out of the system.
5. Install the new freeze valve. To do this, you will need to reverse the steps you took to remove the old valve. Start by placing the new valve in the same position as the old one, and then secure it in place with the mounting bolts or screws.
6. Refill the cooling system. Once the new freeze valve is installed, you will need to refill the cooling system with the appropriate type and amount of coolant.
7. Reconnect the negative battery cable and start the engine. This will allow you to test the new freeze valve and make sure it is functioning properly.

It is important to follow these steps carefully to ensure that you replace the freeze valve correctly and safely. If you are not comfortable with performing this task yourself, it is recommended that you seek the assistance of a qualified mechanic.

Tengo una Cadillac srx 3.6 no tiene chispa, ya cheque el cran chap y est? bien alguien que me de un consejo que puede ser?

NO PROBLEM TOLD. JUST A RELAY HUNT. IT'S ALL HERE https://eautorepair.net/Marketing/Default.asp

https://www.youtube.com/watch?v=eykkKG1O4vo

bad fan. for fuse blow or relay to it dead. or clogged RAD tubes(inside) tests are easy ,ask. at high speed cooling system needs no fan as you slow it does. all cars /trucks. scan the PCM (car) yet< it may tell you why. fuses ?

books on 32 year old cars are not easy to find and no digital docs then. sorry none. buy the service manual used off fleabay is best path on any old car. USA car, not told? no engine told of 3.

• 4.5L & 4.9L Engines
• 4.6L Engine

sorry not answering for all 3 today. lazy I am. fuse is fuse 6, fuse box. "fuel + oil pressure read https://eautorepair.net/Marketing/Default.asp at random 1990 this car I see this. h relay 6 pump 20amps online documents stink, only random scans of 500 page books lost.