2005 Toyota Previa 2.0 - Page 4 - Answered Questions & Fixed issues

year make model?

FixYa Premium Support

YOU MAY WANT TO CONSIDER SPRAY BELT DRESSING ON THE BELTS .. UNLESS THEY ARE WORN ALREADY THEN JUST CONSIDER REPLACING THEM.. THE BELT DRESSING SPRAY IS ONLY A FEW BUCKS AT ANY AUTOPART .. FIGURE YOU CAN START OFF CHEAP.

Its not very easy job to replace the broken drive shaft and harmonic balancer.--- It requires proper tools and proper procedure to do this.The required tools you can get from local auto part store, for the procedure, click this link below:--- http://technoanswers.blogspot.com/2011/08/how-to-replace-drive-shaft-or-harmonic.html ------------ This will help.Thanks.Helpmech.

have you checked the level in the expansion bottle ?? thats where the low level sensor is situated if i remember rightly its at the back left side on the firewall and its a devils own job to get too ,but i could be confused with another make of toyota so check it out under the bonnet first before you go any further

get your owners manual out of the glove box, find fuse panel. there is a legend in the manual and on the back of the panel cover as to what is what. find the fuse for the airbag and remove it. then wait a half hour before disconnecting any of the airbag connections.

Your door may be binding in the guide tracks. Check when the door opens. You could try spray lithum grease if you find that the door does bind.

You will have to check with local auto part store.In most of the cases, you get compatible rods for this.But exactly whats your car model is whats the engine model is, whats the exact year it is.For very old car models, getting parts will be difficult. ------- Still you can try autozone stores for parts.----- If you want to get parts in discount. Click this link below:---

To Order car parts online:--To get heavy discount on car parts .Click this link below:----
http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html ----------- This should help.Thanks.Helpmech.

Toyota 2.2 TD engine type: 3C-TE

General: Allways check the timing marks before timing belt removal!

Instructions:
1. Remove the ancillary drive belt
2. Remove the timing belt upper cover


3. Remove the glow plugs
4. Turn the cranckshaft to TDC for cylinder 1

5. Remove the crankshaft pulley centr bolt

6. Remove the crankshaft gearwheel

Check the oil level in your engine, and top it off. If it has been a while, go ahead and get an oil change.
Also, check your radiator fluid level, as well as your transmission fluid level.
If this sound is only present when you first start the van, it is probably just low on oil. If the engine hasn't been rebuilt, you may have oil leaking from your piston rings and onto your spark plugs electrodes, causing inefficient combustion.
Depending on how many miles this engine has, how hard it was driven, etc., it may be time for a rebuild if this problem gets worse. Main and rod bearings, valve springs, valves, etc. all wear out over time, and lead to louder than normal engine sounds. I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Have you replaced your oxygen sensor ? Problem you just describe points to that, if not enough air will cause this, let me know , Mike from Fixya

That is too difficult to explain here. Search "rear disc brakes Toyota" on YouTube.com for some videos. You may not find a toyota but most are similar.

You need to perform a compression test to verify mechanical intergirty of the engine. Given that it has overheated at least twice from you have stated, it is possible that the head gasket has been damaged and requires replacement. Check your oil and see how it looks. If there is water in the oil system, you will need a head gasket. 1. check the oil 2. if the oil is good, run a compression test. Let me know what you find.

Do not move the vehicle- so do not start the engine but have it towed for replacement of the cam belt with the proper spare and the timing set to the factory standard.

Loosing coolant, white smoke= blown head gasket.

hi.
it could be listed as a tie-rod end, or tie-bar end.
it may also be shown as a stabiliser bar.

you may find you have to buy the complete rod as some of the ends were not removable.
it may be worth asking the mot tester is he knows what they are called

Probably have a rear light ,turn signal ,or brake light out.