2005 Toyota Previa - Page 7 - Answered Questions & Fixed issues
Key fob broken cant get
if its a genuine toyota part, ANY toyota dealer can order on up for you (its gonna cost)you will then have to get it coded by a dealer.
I have a Toyota Previa
The obvious will be to check the fuse, which I'm sure you have....
- Next, locate the relay in the fuse box, There should be a directory on or inside the box lid.
- Using a simple test lamp, remove the relay and identify the coil side and the switch side of the relay
- The switch side will have the larger terminals.
- Take a thin piece of electrical cable and strip off about five millimeters of insulation from both ends....On one side leave the wires intact and on the other use ONE strand of the wire.
- Push the multi strands of wire into the power side of the relay socket....and then using the single strand of wire.... touch and remove (less than half a second) the wire into the output side of the switch.
- If the horn sounds as I suspect it will.
- We go inside the cabin to the steering wheel.
- I believe that for this job you should take it to a shop, This part of the work can be dangerouse
- But if you'd like to carry on knowing there is danger, we can continue at your own risk, realising that the air bag may be ignited.
- Remove the fuse for the air bag.
- Reach behind the wheel and locate the fixing screw holes.
- There will be four.
- Use a machine (star screw) driver and remove the screws.
- Lift off the Air bag unit and unplug it.
- Loosen and remove the center nut from the steering wheel and using a puller pull of the steering wheel....
- Turn the wheel over and take note of the unit fitting.
- Remove the damaged unit and fit the replacement, making sure to align it as per instructions.
- After replacement, assemble, making sure of steering wheel alignment.
I'd be happier if you take it to a workshop, but happy honking either way....Regards Johngee10
My Toyota Estima Lucida model 1994 is overheating
first check the coolant level, then check to see if the fan is working.
if low on coolant then fill it up and check for leak.
if fan don't come on then check fuse and wiring
if you have a fan driven by a blet then do not have to check the fuse.
10/31/2010 12:03:30 PM •
Toyota Previa...
•
Answered
on Oct 31, 2010
•
516 views
Hi... i have a 2001
The flashing light is a fault code. The vehicle should be taken for a scan at your local shop.
Regards Johngee10
Toyota 2004 + rear door
Take off your door panel and take a look. You can open it by manually pulling the door handle level.
You want to pull the level with the yellow tab to lock/unlock the doors:
And you want to pull towards the front of the car for on this level that my hand is on to open the door.
Thanks. Keep updated for any more query. You
can rate this solution and show your appreciation
How to stop water pump
you dont ...... you change the water pump always use new stay away from rebuilt or remanufactured pumps . its probably time for a timing belt also if your car has it
P1305
P1305 Igniter Circuit Malfunction - No. 2
Call or visit your local toyota dealer. Purchase an ignition coil. $85 The #2 cyclinder is the passanger side front.
X0 -this one
XX
XX
XX
Take that plastic V8 siver cover off and
throw it away. Unplug the wire connection that looks like the piece you
purchased. Remove the 12mm bolt that is holding the old one in place. It
is pushed onto the sparkplug below. Pull out the old one. Push in the
new one. reinstall the 12mm bolt. plug in wire connection. I believe
the #2 can be reached without removing the plastic air intake.
Hope helps (remember to rate and comment this).
How do you get the
have to go from inside the trunk through back of housing. may need to remove a panel covered by carpet to expose the panel. then just unscrew the bulb holder and swap out the bulb.
I'm in the middle of
Dont remove the cam gear until you remove the crank shaft bolt.If you turn the crank with out the cam gear in place you may bend some valves.And damage the head,or a piston as well.
You can use a bar, and a socket on the crank bolt, if it clears everthing and rests on the frame work,then engauge the starter,this will loosen the crank bolt,but dont start the engine.Just a few hits on the key.Stand clear of the bar,!You may have to heat the bolt head a bit,as well.The bolt may have had locktite installed on the threads.Have the battery fully charged.
I have a toyota townace
when you squeeze the hoses are they soft and bulging at the clips.then try looking for the leak around these....
Hi we charged the battery
Is your serpentine belt in good condition? If not, replace it. You'll need a volt meter to check out how much the alternator is charging. Attach it to the negative & positive terminals of the battery & start car. It should read 13.2 to 14.6 volts. If it does not, you have either grounded a positive wire somewhere or your new alternator is not working. Have it tested at the automotive shop you bought it at. Good luck, I hope this helps!
Driver side door will not
u should go to the body tech. it maybe the cabels from inside or the locker is not working as well as it must be
Toyot Previa - high mounted stop light
This is slightly counter-intuitive, but the plastic lens needs to go in and up before it comes out. After removing the two screws, use something thin and flat to pull down on the underside painted part of the wing between the two screws. A little bit of prying downwards. Two raised lips become visible - they are holding the lens from being able to be pushed up and in. A second pair of hands could help. Then use your thumbs on the lens close to the screws, gripping with your fingers on the top of the wing and squeeze up. POP!
10/9/2019 1:06:29 PM •
Toyota Previa...
•
Answered
on Oct 09, 2019
•
1,298 views
Not finding what you are looking for?