3.0L V6 (and box behind it?)post a problem fist the A/t box list of failures is 20 paged + long, name one?that way we the blind can be on the same page?and there is not just one box solenoid/the word is solenoid's (MANY INSIDE IT,DEEP)say my a/t box shifts funny?, late? or slips? or will not shift in drive,1,2,3,4,5 or sticks at 2.??????? DRIVE DEAD,REVERSE DEAD , low deadPRNDLsome of these 3.0L have a mazda transmissioncalledMazda trans.; Trans. code FNR5seen here allhttps://www.rockauto.com/en/catalog/mercury,2007,milan,3.0l+v6,1434320,transmission-automatic,shift+solenoid,8476inside the transmission ,vb ,valve body. 99% of cars FOR SURE 2007 !!!!all.6 solenoids seen here best https://www.amazon.com/Mazda-FNR5-6PC-SOLENOID-KIT/dp/B073HG31TWbut not A?T box but is was.not the console shift lever park/lockout / solenoid.?no actual problem told? just a hunt. (vague)shifter lever stuck in PARK???????
Underhood battery junction box . Fuel pump not working ? Your vehicle has electronic returnless fuel system , has a fuel pump driver module , fuel rail pressure sensor that is a input to the PCM - engine computer . PCM communicates fuel needs to the FPDM which controls the fuel pump with PWM - pulse width modulation . The fuel pump does not run all the time.
Ford Electronic Returnless Fuel System Diagnosis Part 1 Ford
Find fuel pump relay location here http://www.bbbind.com/free-tsb Enter vehicle info. Year , make , model an engine . Under system click on electrical distribution ,then under subsystem click on fuse panel . Click the search button then the first blue link .You will see battery junction box diagram
Check you water damp outlet is not blocked. This causes build up of water inside the cabin after a while. Owner manual should help you indicate, otherwise,under the car the outlet should be seen and if no water dispenses when aircon is on, it’s definitely clogged
Well you could have a couple problems. First and maybe the simple to check. Open the hood and see of the shifter is moving when the inside is moving. Connectors and brackets do break. You think the slave is working but only way to know is with the car off and in gear. Try pushing the car if it does not roll then the clutch is working and nothing is broke letting the car roll easy. Press the clutch and if the car rolls then you know the clutch is working. Yes it's a simple test but it works then at least you know it's not the clutch. If you can't get the car in gear when running but you can when it's turn off. Good guess the master cylinder slave or a hose has gone bad. Check the fluid see if it's empty. If it is then it's clear there is the problem and filling the reservoir will show where it's leaking once you see the leak. Bleeding the system after replacing parts will be the last thing. If everything seems good. Last and worse case would be the transmission broke or cv shaft broke but then it would roll easy and make alot of grinding noises depending on where it broke. Trany shop can always help figure out what's wrong and give an estimate for parts and labor
Probably a voltage sensor locking the signal to start the car. Check the battery and charging system. Happened the other day to my wife. Battery was weak. don-ohio
There is a lockout that keeps the starter from turning the engine over unless your foot is on the brake. When a foot bumps the switch which is usually on the upper brake pedal level, the switch can either break or move where it will not work.
Often you will notice the brake lights do not work, but there are some that will break and short out in different ways.
If it keeps throwing up the same codes it may not be a sensor issue directly. There is a possibility that the wire harness, ground, and/or connector to that sensor is faulty, or the computer itself has some bad or corroded connections.It seems you need a hands on Guru to find the issue - with a pulse short finder. These newer vehicles have overly complex electrical systems that 'loop' power and ground connections through several components, as well as the onboard computer, and a short finder may be the only solution.
I hope this helps to steer you in a feasible direction - and Thanks for using Fixya!!
I am guessing you mean the door lock codes. If no one has changed them, you may be able to find a tape strip with the 5 numbers on it in a hidden place. Often these strips are put on trunk hinge brackets or under doors or other body panels.
This holds true for the original number. You may be able to get the info from the Dealer if the Vin# has a record of it.
But-the number can be changed by an owner. It can be anything now if it was changed. In that case, a new lock would be needed.
Sorry to say its not designed to be checked by the car owner.
There is a check plug that you can access if you have the factory instructions and the tools to do the job.
If this is a car lot purchase, they should have at least a 30 Day guarantee. You can get FREE help at Autozone, Advance, or Oreilys parts stores as they give free scans to interpret the Code for the wrench light.
This car MIGHT still be under warranty? Have you noticed if the brake lights are stuck on all the time? This sometimes happens when the switch on the pedal sticks or pops out of place. Something might be draining the battery. A power seat switch can do it.I'd take it to Ford and ask them if it's under warranty or service bulletin.They might fix it for free and at least they can tell you what's wrong. don-ohio (:^)
take it back to the dealer they didnt install the coil or electric distubutor properly because of the misfire its causes o2 sensor to give bad reading .
Perhaps you have the headlight dimmer which adjust the dash illumination adjusted so far that it turned on the interior lights. Back it off a bit.
Or there may be a fault in one of the door switches making the light believe a door is open.