20 Most Recent 2009 Jeep Patriot Sport - Page 9 Questions & Answers

vacuum lines dry-rotted out possibly unhooked from position , faulty fuel pump *, and possible fuel-filter, maby a gas line is leaking , plug wire or wires maby one that is rubbing and causing it to arc and lose power that way many possibilities exist ...could be a manifold intake leak .or !

you could try a few things to isolate the issue 1st put a clean piece of cardboard under the vehicle to ensure the vehicle gas line is not leaking start the vehicle to see if there is any signs of that ,.
then visually look for any vacuum lines that may have come undone or simply are dry-rotted by bending them if they are replace them look for any arc's in the plug wires by using a plastic spray bottle and adding only water and spray the wires with the vehicle running this will show any arc's bending them in the same way will give a clue if they are in need of replacement ..as well for a few dollars a can of brake cleaner fluid or carburetor /choke cleaner and with the motor running spray around the intake manifold as well as all connections between the vacuum lines

you can take it to most parts stores and ask for a fuel pressure test and they will provide you an exact fuel pressure need for your s as well as what it is running at ..
you may also want to borrow their code reader and simply connect it and turn the key to on not starting it and allow the diagnostic tool to communicate with your vehicle ...if any thing is found it will tell you or give you a code //Write it down and or if a readout is present you may wish to purchase your part/s while there ,
check all your fluid levels as well but it sounds to me like one of my above suggested places to look at ...the basics you could say 1st

hope this helps you and is an easy fix for you .

hallo
check battery. when you start the car, battery voltage (for second) fall under 8V and confuse electronics
Marko

You can download the Owners Manual from HERE

Hope helped.

contact the dealer they have a special tool to check the level

The mileage estimates on your sticker are EPA mileage estimates, which are notorious for being inaccurate. They overhauled their testing standards for 2008, but real world mileage can be much different. Driving like a grandma doesn't mean much. Living in areas with a lot of hills or mountains will decrease mileage, as will rain and snow. Check your tire pressure often, as improper tire inflation can hurt your mileage. Other than that, you're probably getting average for that vehicle. Welcome to SUVs.

the jeep patriot does really have gears since it is a CVT transmission. and since that it has been replace as you said i think that you may have an electrical problem of some sort whether it se a module or software for the module, wiring or a sensor

It is a known issue.

The driver side power seat in my 2017 Jeep Grand Cherokee

JustAnswer https://www.justanswer.com > Jeep Questions Nov 28, 2023 - Every other part of the power seat works (lumbar, vertical adjustment etc) but for some reason it is not moving forward or backwards. I checked ... 1 answer · Top answer: Welcome to JustAnswer. Sorry to hear you have a frustrating experience. I'm glad to assist ... Missing: Overland. ‎' Show results with: Overland.

Driver seat is stuck rearward

Jeep Garage https://www.jeepgarage.org > threads > driver-seat-is-st... Aug 19, 2012 - I have 2004 Overland that automatically moves forward and rearward when unlocking and locking the vehicle. The seat is stuck all the way ... Easy exit seat not working Feb 18, 2018 Driver seat won't move forward Apr 4, 2016 Seat Memory, Easy Entry/Exit not working Aug 3, 2018 Memory Seat not working Feb 23, 2010 More results from www.jeepgarage.org

FIX: front seat stuck forward or seatback won't return to ...

JLwranglerforums.com https://www.jlwranglerforums.com > forum > threads Jan 8, 2022 - It's a known issue. There is one for each seat and it moves along the door-side track. The left and right sides specific and not switchable.

old fords have them and yours does tomine not. ,not my JK Nor wk. I have your real factory service manual here on screen 2. yes, replacing the alternator with the battery connected does blow a fuse. in 1 nano second fast. BOOM , let the smoke out. but saved by the link. OKAY you were right the liberty has that link you were right, it has links ! this is your actual car, wiringi have it all there. FSM PDF real.

So it really is only a jeep XJ body ,not a real jeepsure loved by all sure.jeep has 2003 avalanche LS5.3 ENGINE AND 4L60E TRANS WITH A 6" Lift (ouch) on 37" tires with 1979 Ford 3/4 ton rear ends.with NP231 transfer, np207 gone now with new NP231 transfer case from the '91 YJ ?, NO, from a CHEVYI bet now it is NP231C box, the C means Chevy box.with 2H, 4H, N, and 4L,, this is part time 4wd, not full and is not for the 4wheeling on pavement. only offroad or on ICE.ICE means, just that or snow or snow over ice. (sorry captain Obvious, just left the building,now)end ICE answersbegin, 6" lift extreme problemsthe real problem is the LIFT that high.3 "easy4 hard6 "extreme lifts.IT fails in 2wd mode too, that is because U-Joints have limits. (all do) and the lift span chart below.(angle) post.nothing else needs to known, but U-JOINT ANGLES are all WRONG.SOLVED,. the 6" lift done wrong. YJ is a very short Wrangler and very short rear prop shaft.that means Prop(rear) drive shaft angles are dead wrong. (solved the reason on 1 fact)DOne with no SYE kit. "slip Yoke Eliminator"'https://www.amazon.com/Heavy-Eliminator-52231-18676-60-Driveshaft/dp/B00FDWL7PMdone i bet with no shims for rear axle LEAF spring perches , to get angle right(they sell shim kits)the answer You need a double cardan or CV (same piece different name) at the TC case, this will require a new yolk. You will also need to shim the pinion angle to get the driveshaft and pinion within 2 degrees of each other.

First you will need to determine if there is a problem with the electrical system or fuel system. Connect a fuel pressure gauge to the fuel rail to see if you have pressure when the vehicle dies. It it maintains pressure and the vehicle dies, then check to see if there is a spark issue. Fuel issue could be bad/weak fuel pump, bad relay or restriction in fuel delivery system. No spark could be ignition coil, bad computer, bad electrical connection or relay. To check these systems you need special meters and scanners. Best to take to a repair center.

The most likely reason is a faulty switch or a faulty relay or problem with the Body Control Module computer. https://www.google.com/search?q=auto+electrician+near+me ..

1. Faulty Instrument Cluster: The instrument cluster itself may be defective or damaged. Over time, electronic components can degrade, leading to malfunctions.
2. Fuse: Check the fuse box for any blown fuses related to the instrument cluster. A blown fuse could disrupt power to the cluster, causing all the gauges to fail simultaneously.
3. Faulty Wiring: There could be a problem with the wiring harness or connectors that supply power and data to the instrument cluster. Loose connections or damaged wires can prevent the cluster from receiving the necessary signals.
4. Vehicle Speed Sensor: The vehicle speed sensor (VSS) is responsible for providing speed data to the instrument cluster. If the VSS malfunctions, it can cause the speedometer to stop working, and it may affect other gauges as well.
5. Engine Control Module (ECM): The ECM communicates with the instrument cluster to provide data for various gauges. A malfunctioning ECM could disrupt communication and cause all the gauges to fail.
6. Grounding Issues: Poor grounding can lead to electrical problems, including instrument cluster malfunctions. Ensure that all ground connections related to the instrument cluster are clean and secure.

Given the complexity of diagnosing electrical issues, it's advisable to have a qualified mechanic or automotive technician inspect your vehicle. They can use diagnostic tools to pinpoint the exact cause of the problem and recommend the necessary repairs. Additionally, if the issue is related to the instrument cluster itself, it may need to be repaired or replaced by a professional.

a hose clamp ?or just guide clamp to the fan shroud.jeep dot com will have it on all jeep web sites, under title cooling systemgood luck, not the 2.4L ESS engine right:2.4L gas as seen on mopar.com sitenow I will read the pages online to youguessing all that. stuffi go to mopar.comand see this. is this a match.if not go there and find it or as them over the counter jeep dealer.or go there, and put you VIN in the boxand find the parts, no better way exists.

This might sound silly but have you checked the switches on the actual light fittings? They usually have three settings. Permanently Off, door controlled or permanently On. If there are no switches on the actual light fitting try pushing the lens itself at each narrow end. Some lenses rock end to end as the switch mechanism.

Have you checked the connectors in the wiring harnesses for the ABS unit and associated components for water intrusion or corrosion? The codes that you've posted (details below) all point to a poor electrical connection in the circuit(s) or an open or short in the circuit(s). That could be either due to corrosion, liquid intrusion, a wiring harness rubbing against something hot or something that vibrates and has damaged the wiring. If the wiring and connections are all intact and there are no opens, shorts to power or shorts to ground, the next think to look at would be the modules and/or sensors to make sure they're operating within spec. U1003 Possible Causes: *Faulty Anti-lock Brake System (ABS) *Module Anti-lock Brake System (ABS) *Module harness is open or shorted Anti-lock Brake System (ABS) *Module circuit poor electrical connection The Diagnostic Trouble Code (DTC) sets if the Anti-lock Brake System (ABS) Module fails to receive bus messages from the Dynamic Sensor for approximately 150 ms. ----- C0020-1c Possible Causes: *Faulty Anti-Lock Brake System (ABS) *Control Module Faulty Hydraulic Control Unit (HCU) *Hydraulic Control Unit (HCU) harness is open or shorted Hydraulic Control Unit *(HCU) circuit poor electrical connection The Hydraulic Control Unit (HCU) consists of a valve body, pump motor, and inlet/outlets for the brake lines. The combined HCU and Antilock Brake System (ABS) module is located forward of the master cylinder. The Anti-Lock Brake System (ABS) Module monitors the ABS Pump Motor. The ABS Module sets the OBDII code when the ABS Pump Motor is not to factory specifications. ------ U0125 Possible Causes: *Faulty Dynamics Sensor Dynamics Sensor *Harness is open or shorted Dynamics *Sensor circuit poor electrical connection The Diagnostic Trouble Code (DTC) sets if the Anti-Lock Brakes System (ABS) Module fails to receive bus messages from the Dynamics Sensor.

If the fan works on med but not high or low it is an indicator that the resistor has gone bad. Since the motor works sometimes, it's a pretty safe bet that the motor is good. A 12v test light will tell you if it's the switch or the resistor.

If your transmission does not have the output shaft speed sensor (42RE automatic transmission) then you do not need the fuse.

You should check out www.reliable-store.com they have info on repair, service, wiring diagram, electrical diagram, fuse diagram, troubleshooting, PCV, owner's/service/repair/parts manual, fault codes, error codes, etc everything on all vehicles. must check it out

https://offroadhack.com/42rle-transmission-problems/ Check with you jeep dealer to see if there are any recalls on your transmission,