Top 20 2008 Jeep Commander Limited Questions & Answers

0helpful
1answer

Fix side view mirror on 2009 jeep commander

what does fix mean. double posted now, as anon. no less. is it broken or motors dead? what? tell symptoms then ask how to correct those.
10/20/2014 10:01:07 PM • 2008 Jeep... • 209 views • 0 helpful votes
0helpful
1answer

2008 jeep limted with navi radio touch screen freezing up then restarts

upgrade the maps
12/3/2013 4:36:59 AM • 2008 Jeep... • 153 views • 0 helpful votes
0helpful
1answer

Map sensor location Jeep commander

I've had good luck Googling Youtube videos for this kind of thing. Or you could get a Chiltons/Haynes maual that covers your vehicle.
9/15/2019 4:31:12 PM • Jeep Commander... • 2,338 views • 0 helpful votes
0helpful
1answer

I'm changing spark plugs on

Yes you need 16 plugs. You will need a good selection of different length 3/8" extensions, as well as a good plug socket with the rubber inside to grip the plug connector. You should also invest in a rubber plug installer tool (they are about 6" long and will pop over the terminal of the plug and can be used as a handle to make installation easier) These things are a pain to change, but it can be done without removing anything major. I use an old quilt over the engine so I can lay over the top to make reaching things easier. Have fun, good luck.
2/3/2018 5:45:03 PM • Jeep Commander... • 170 views • 0 helpful votes
0helpful
1answer

2009 Jeep Commander --- Ignition problems. For

Hey Anon, Is this a total electronic key,,(push button start)..if so, its an electrical issue. If its a standard key urn ignition. try some DRY graphite on the key.. it will lubricate the switch without the mess of liquids... put the key in and out several times, put some more dry graphite on the key and repeat.. give this some time to work,, if this does not improve the switch.. its time for a new switch assy,
6/24/2017 6:06:03 PM • Jeep Commander... • 503 views • 0 helpful votes
0helpful
1answer

My 2012 commander seems to chatter when i put it in drive sometimes it works other times seems like its not catching the secondary cluch

When was the last time you checked the transmission fluid level? It might be that time now.
8/18/2017 1:34:33 AM • Jeep Commander... • 75 views • 0 helpful votes
1helpful
1answer

2007 Jeep Commander Check engine light is on (but that has been on for awhile.) Electronic Throttle Control (ETC) warning light just came on and my temperature doesn't move very from C. Any ideas?

thermostat is bad probably, not sure if the xk has a built in obd or not but turn the key on and off (almost till starting) 3 times called the key dance should spit a code on your led readout below spedo
3/23/2017 2:10:31 PM • Jeep Commander... • 443 views • 1 helpful votes
0helpful
1answer

Where is the fuse located for the tail light on a 2007 jeep command

commander, is a grand with diffr, rear seats, bla bla. the book is free, for the WK posted 300 times. click free here, then click WK. http://jeepdied.com/books.html THE BETTER question is HOW do they work?? IT'S NO 1993. they are park lamps, tails is old skool name, ok no prob. parks are front /rear and sides so all parks dead. be key fact, even the dash dimmer uses the parks (first click of the HL switch is PARKING LAMPS) I might add that we have answered this maybe 3 times here. already. ill do it one more time. in the same book chapter 8w covers this, called exterior lighting or lamps. it is digital controlled. the TIPM underhood does this. the TIPM hears the network commands for parks. and closes its PARK relay this relay then runs all park line feeds. front and rear the license plate is a park lamp. too. the 3 fuse are 8,9,10 in the TIPM under hood. clearly marked park. if you look there the lids has all then names , marked. that does rear. 8w-51-4 covers rear. same fuse 8 left 10 right. if 10 blows the cab switch bank goes dead for illumination. but you never said how many are dead. if all are dead and the relay is ok the programming is bad or you forgot to see DTC errors scanned. if all lamps are dead, it must be scanned, or replace relay 2005 up'
1/19/2017 10:54:15 PM • Jeep Commander... • 1,359 views • 0 helpful votes
0helpful
1answer

Engine light on jeep commander xh limited

same on all cars. USA< (by laws,) 1988 to now scan it. USA fed laws. created OBD. long long ago others vast (copied ours and even added to them) even as late as 2010 it can be 1 of 100 things even a lose gas cap. scan it get it scanned (a car repair shop, all can , in USA every one) rent a tool buy one barrow one
2/27/2017 12:58:28 PM • Jeep Commander... • 68 views • 0 helpful votes
0helpful
1answer

Blowing out cold air even when the heater is set to hot setting. Feels like cold air is coming in from the outside. The colder it gets outside the colder it gets inside. 2007 jeep commander

ok, first the engine gets hot, if not there will no cab hot air. so if you scan it the PCM shows the ECT reading over 180f, does it. if not , the thermostat is bad. in order !!! blower works so not blower. leaving dampers, does the HVAC self test pass? if damper are in heat mode, that leaves only 2 left (possible air filter there? ,its and option) in the dash HVAC box. the heater core is packed. (in air side or water side)
11/20/2016 7:05:30 PM • Jeep Commander... • 286 views • 0 helpful votes
1helpful
1answer

Block heater for commander what type? where is the best place to install it? inline or circulating?

no year car stated. each has pros/cons, like all things do. used only at home or work and home.? is the at work power on a timer, ? there are 3 types. mag mount (slapped on to oil pan steel pan) freeze/core plug heater. inline loop heater. (id go for this, it many draw less current) less current can equate to not blowing the fuses at work. or a home, and no surprises in the morning. (or) or the most easy to installed be, best for you. who knows what you would like.?
1/3/2017 8:24:53 PM • Jeep Commander... • 48 views • 1 helpful votes
0helpful
1answer

How to install carriers bearing and pining gear on jeep commander

Just like any other 3rd member. If you do not know what you are doing, I would not suggest doing the job yourself. You need to have a certain amount of pre-load on the pinion at the crush sleeve. And you need to have the run out of the pinion and ring gear depth shimmed correctly to prevent noise and premature wear.
12/22/2016 7:57:35 PM • Jeep Commander... • 46 views • 0 helpful votes
0helpful
1answer

Check engine light on 2007 jeep commander, p0750

what motor do you have
11/8/2014 8:44:50 PM • Jeep Commander... • 1,456 views • 0 helpful votes
0helpful
1answer

Remove headrests jeep commander

open glove box. extract opr guide read it.
8/22/2014 12:00:50 AM • Jeep Commander... • 857 views • 0 helpful votes
0helpful
1answer

Po13c code how to fix po13c code

what year JEEP> is that so hard to tell? is your jeep and export model, not in USA?> 3.7L fix. ? fixing is last (unless gue$$ing is cheap plan?) diagnosis is first. (after doing the skipped tuneup) first/ first is to read the JEEP FSM on what it is , and the steps to isolate all errors. (true cause) p013c (p zero) i have 2010 3.7L and matching FSM. book. i think it's 02 B2S2 errors. (bank2 sensor 2) aka as 2/2 sensor. this nails it. http://www.jeepforum.com/forum/f67/2007-wk-code-p013c-1325479/#post13011898 when you cut the throttle, the cat is full of fuel and will not lean out.. so the o2 rear sticks high. (low oxy) the cat eats all oxygen if its overloads with HC, (fuel) this DTC catches that event. my guess? is the right bank is running rich the cat is overloaded and this test fails. not sure why.? no could it in the net bunny cloud. we would check the live data stream on the right bank, 2,3,6 bank 2. for gross fuel trim issues, or the o2s acting odd on that side. S1 and S2. are you saying you can drive and no other DTCs are thrown? no P03xx codes ever. are the spark plugs fresh, not 50k old, ever do a tune up.
7/13/2014 2:44:10 PM • Jeep Commander... • 1,399 views • 0 helpful votes
0helpful
1answer

Need help how to take a radiator of a jeep commander

depends on year, and engine, there. zero input there. 2005+ sure so what engine, cooling varies by ENGINES. read the 04 WJ might match chapter called cooling. page 42? or? only you know engine. 14 steps. http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service pretty much any car (short) drain it. remove all hoses and wires. and fans and shrouds then unbolt it. lift it out. this your first RAD, ever read car repairs for dummies (no dig , real book)
8/28/2014 1:39:06 AM • Jeep Commander... • 228 views • 0 helpful votes
0helpful
1answer

How do i fix the electronic throttle control

Hello, The problem most likely lies in the Throttle Pedal Sensor which is attached to your Gas Pedal....You'll probably have to change the whole Pedal+Sensor, it's easier that way...Good Luck and Let us know if it fixes your problem...... Regards, Peter (Ireland)
6/30/2014 5:07:22 PM • Jeep Commander... • 662 views • 0 helpful votes
Not finding what you are looking for?
2008 Jeep Commander Limited Logo

3 questions posted

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Commander Jeep

  • Commander Jeep

Most Popular Question

fix side view mirror 2009 jeep commander

  • Cars & Trucks
Loading...