20 Most Recent 2007 Jeep Commander 3.0 Questions & Answers

0helpful
1answer

The check engine light is on my 2007 jeep commander

Usually is one of your sensors but you can get it checked by auto zone for free on the diagnostic machine..
3/16/2016 4:28:11 AM • 2007 Jeep... • Answered on Mar 16, 2016
0helpful
1answer

How do I remove the 3rd row headrests from a 2007 Jeep Commander?

Their held in with a snap ring or look at where they mount to the seat. If you see screws/bolts, take them out. If not you will have to pry/pop them out.
11/30/2014 6:14:34 PM • 2007 Jeep... • Answered on Nov 30, 2014
0helpful
1answer

I have a steady whining humming sound from my rear end of my 2007 jeep commander when u start it and push on gas. what could it be?

rear end (I use and electronic stethoscope to find all that) but rear end. is a big place.. bad U-joints top that list (repeat) bad axle bearings. brakes bad, there. or the warning devices there for early brake warn. bad 3rd member, gear sets or bearings in same or pinion. my guess is car is moving right> if not moving ,its dying rat up in there.or loose parts.
10/21/2014 4:44:45 PM • 2007 Jeep... • Answered on Oct 21, 2014
0helpful
1answer

Radiator fan

what engine, there are 3 in the USA. gas or diesel.? the big engine has"?a "two high pressure lines at hydraulic fan drive." 5.7L engine. before working on any car, know what engine is there.......???????? the fan just behind the engine rad, comes on, on a dead cold enigine? CEL (check engine lamp) on key on, then turns off , engine running and then CEL stays off all the time.????? i no, scan it. there are 9 DTC errors for the fan alone. scan it. one one engine, p0692 , tells you , fan2 (high) is stuck on. got that? there are 2 fans on the electric fan type engines. got 2 fans? and 2 relays and both are controls all the time by the MFC, module , front , control. p0480/81 is for the hydraulic, fan... controlled by 2 modules.... ill wait for engine size ......
12/25/2013 1:39:00 PM • 2007 Jeep... • Answered on Dec 25, 2013
0answers

Tipm location

Be the first to answer 4/26/2013 1:03:21 PM • 2007 Jeep... • Posted on Apr 26, 2013Be the first to answer
0helpful
2answers

Where is neutral safety on 2008 jeep commander

The neutral safety switch for an automatic transmission is located inside the transmission case or in the linkage that allows the vehicle to shift gears. This switch prevents you from starting the engine when the transmission is in any gear other than Park or Neutral.

4_13_2020_6_59_13_pm.png
4/13/2020 6:59:14 PM • Jeep Commander... • Answered on Apr 13, 2020
0helpful
1answer

Map sensor location Jeep commander

I've had good luck Googling Youtube videos for this kind of thing. Or you could get a Chiltons/Haynes maual that covers your vehicle.
9/16/2019 3:45:00 AM • Jeep Commander... • Answered on Sep 16, 2019
0helpful
4answers

Where is the a/c drain located on a 2008 jeep

If you look at where the heater core pipes run into and out of the firewall under the hood. there should be a small rubber/plastic tube coming out of the firewall near these pipes. this is the drain.
7/25/2019 1:41:58 AM • Jeep Commander... • Answered on Jul 25, 2019
0helpful
1answer

I'm changing spark plugs on

Yes you need 16 plugs. You will need a good selection of different length 3/8" extensions, as well as a good plug socket with the rubber inside to grip the plug connector. You should also invest in a rubber plug installer tool (they are about 6" long and will pop over the terminal of the plug and can be used as a handle to make installation easier) These things are a pain to change, but it can be done without removing anything major. I use an old quilt over the engine so I can lay over the top to make reaching things easier. Have fun, good luck.
2/4/2018 1:33:00 AM • Jeep Commander... • Answered on Feb 04, 2018
0helpful
1answer

My 2012 commander seems to chatter when i put it in drive sometimes it works other times seems like its not catching the secondary cluch

When was the last time you checked the transmission fluid level? It might be that time now.
8/18/2017 2:16:18 AM • Jeep Commander... • Answered on Aug 18, 2017
0helpful
1answer

2009 Jeep Commander --- Ignition problems. For

Hey Anon, Is this a total electronic key,,(push button start)..if so, its an electrical issue. If its a standard key urn ignition. try some DRY graphite on the key.. it will lubricate the switch without the mess of liquids... put the key in and out several times, put some more dry graphite on the key and repeat.. give this some time to work,, if this does not improve the switch.. its time for a new switch assy,
6/24/2017 6:24:36 PM • Jeep Commander... • Answered on Jun 24, 2017
0helpful
1answer

2007 Jeep Commander Check engine light is on (but that has been on for awhile.) Electronic Throttle Control (ETC) warning light just came on and my temperature doesn't move very from C. Any ideas?

thermostat is bad probably, not sure if the xk has a built in obd or not but turn the key on and off (almost till starting) 3 times called the key dance should spit a code on your led readout below spedo
3/24/2017 2:20:06 AM • Jeep Commander... • Answered on Mar 24, 2017
0helpful
1answer

Engine light on jeep commander xh limited

same on all cars. USA< (by laws,) 1988 to now scan it. USA fed laws. created OBD. long long ago others vast (copied ours and even added to them) even as late as 2010 it can be 1 of 100 things even a lose gas cap. scan it get it scanned (a car repair shop, all can , in USA every one) rent a tool buy one barrow one
3/3/2017 7:10:45 PM • Jeep Commander... • Answered on Mar 03, 2017
0helpful
1answer

Where is the fuse located for the tail light on a 2007 jeep command

commander, is a grand with diffr, rear seats, bla bla. the book is free, for the WK posted 300 times. click free here, then click WK. http://jeepdied.com/books.html THE BETTER question is HOW do they work?? IT'S NO 1993. they are park lamps, tails is old skool name, ok no prob. parks are front /rear and sides so all parks dead. be key fact, even the dash dimmer uses the parks (first click of the HL switch is PARKING LAMPS) I might add that we have answered this maybe 3 times here. already. ill do it one more time. in the same book chapter 8w covers this, called exterior lighting or lamps. it is digital controlled. the TIPM underhood does this. the TIPM hears the network commands for parks. and closes its PARK relay this relay then runs all park line feeds. front and rear the license plate is a park lamp. too. the 3 fuse are 8,9,10 in the TIPM under hood. clearly marked park. if you look there the lids has all then names , marked. that does rear. 8w-51-4 covers rear. same fuse 8 left 10 right. if 10 blows the cab switch bank goes dead for illumination. but you never said how many are dead. if all are dead and the relay is ok the programming is bad or you forgot to see DTC errors scanned. if all lamps are dead, it must be scanned, or replace relay 2005 up'
1/20/2017 4:37:26 PM • Jeep Commander... • Answered on Jan 20, 2017
Not finding what you are looking for?
2007 Jeep Commander 3.0 Logo

Popular Tags

21 questions posted

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Commander Jeep

  • Commander Jeep

Most Popular Question

remove 3rd row headrests from 2007 jeep

  • Cars & Trucks
Loading...