20 Most Recent
2005 GMC Canyon Extended - Page 6 Questions & Answers
Used a code reader on
EVAP System (Gross Leak ) PO455
Should be easy to find
That is the largest of leak codes
The door lock/unlock on my
you need to check the battery in the key fob remote . If the battery are good . the remote will need to be tested to make sure it is capable of transmitting (only place i know that can test them is the dealer ship but you could call your local parts store to see if they can test). If the the remote test good then it will have to be reprogramed or relearn to the truck .I belive if it needs to be relearned or programed you will need to have that done at a shop with a proper scan tool .
Even though I have put
check for loose connections on seatbelt stem and under the seat - wires on floor but also under the seat itself. That sensor detects people sitting on seat.
2005 gmc canyon 2800 vortec
Is the check engine light coming on the dash.If yes,then did you got the car scanned.If not? then get the car scanned.At autozone service center its absolutely free to get car scanned.Once the car is scanned,so it will give the codes , and as per error codes the faulty part can be easily replaced.But if the check engine light is not coming on then,the gmc canyon stalls at idle, in this case the IAC valve has to be checked.The iac valve located on the throttle body has to be cleaned and checked.If still the same problem then IAC valve has to be replaced.
---------------
Throttle body cleaner and a tooth brush. make sure you clean around the valve area real well.
Remove the intake, and 4 bolts hold the TB( throttle body) on.
You need to remove the whole thing. Remove the intake, including the vortec bo. Once that is gone you will see 4 bolts holding the TB in. Remove those. Very carefully remove the plus from the TB. You will then have the whole thing removed. Very carefully clean the whole thing with throttle body Cleaner, rags, and a toothbrush. make it look like its polished and then reassemble.You can get throttle body cleaner at local auto part store.----------
This should help.Keep updated.Thanks.Helpmech.
Would like a complete service
You can get complete factory shop manuals from a company called HELM INC they print them for most car companys . There about fifty dollars you may need 2 chevy generaly has two books for a complete set but this is far less then the dealer would charge you . I know i bought mine from the dealer and it cost me over 3 hunderd www. helminc.com
Batterie is not charging we
Hi, have you checked the alternator? Voltage should be at least 14 volts at battery with engine running. If not, or you don't have a voltmeter, remove the alternator and take to parts store for testing.
Thanks for using FixYa.
My front disc breaks are
the only thing that I can think of doing is to open up the zerk fitting ( bleeder ) and trying to force the inner pad inward ( which will compress the piston and release the pressure ). I hate to suggest a big flat blade screw driver to use as a lever, but there is not much room in there to do the compression. try and be careful not to mark/nick up the disk as this will/can cause pre-mature pad wear. if both sides are locked up -- just repeat the same step on both sides. after things get freed up it will be important to figure out why so much pressure is building up in the brake lines,, you might try and flush brand new fluid all the way through the lines and see if that fixes the problem.
c...
I lost the remote to
This usually happens because we use key fabs/remotes but occassionally we do still need to use the locks to prevent the locks from corroding and seizing up. You can spray a graphite lubricant into the lock and working the key into the lock.There is a product called locklube which should be available at your local auto parts vendor.You spray it into the lock lube and work the key in the lock. If this process does not work the lock may need to removed and replaced or rebuilt.
I am getting a p1516
Trouble Code:
P1516 (2.8L L4 VIN 8 Std)Throttle Position Miscalibrated
Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
-
The ignition is ON.
-
The ignition voltage is greater than 8 volts.
-
The system is not in the Battery Save mode.
-
The engine is running.
-
DTC P0068 is not set.
Possible Causes:
-
Use the J 35616 Connector Test Adapter Kit for any test that requires probing the PCM harness connector or a component harness connector.
-
Poor connections at the PCM or at the component--Inspect the harness connectors for a poor terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems for the proper procedure.
-
For intermittents, refer to Intermittent Conditions .
Is there a special tool
Not that I know of, but I feel your pain. I use pliers to compress the spring and then put needlenose visegrips on the cable to hold it back. Then slip it in the slot. Does this make sense?
Periodically, the truck will not
Sounds like your security system is cutting out the starter circuitry, unfortunately if the security module is going bad it may only test bad when it is causing the problem, this is a sure sign of the alarm cut off, perhaps you need to have an alarm specialist check out the vehicle, sometimes you cut out the middleman if you take it directly to an auto alarm security installers facility, check the yellow pages for info in your area. And be sure you bring both remotes if you have them.
Use an alarm company that sells and installs the same alarm that is in your car, if yoyu are having trouble finding any of this information visit the dealership where you bought the vehicle and ask who they use for this repair.
I hope this works, i would try to take care of this soon as the vehicle may shut down one day and leave you stranded in a place God forbid you may not want to be in.
Happy Motoring!!
My truck has been having
There are some
possibilities which you will have to check in this case:--
1) First of all check
the power and voltage to the battery.with meter it will show exact
12 volt if the battery is charged.if the voltage is less get the
battery charged at local auto repair shop.if the battery is internally drained
and not getting charged then its time to replace the battery.
2) When you crank the
truck do you see spark coming at the spark plug? if no then its time
to check the spark plugs and coil pack.if the spark plugs are not worn out and
looks new then its time to check coil pack.the spark plugs gets power to spark
from coil pack.
3) The other thing to
check in this case is the starter solenoid of the truck.
If the battery is
charged and you start the truck then
it gives power to the starter to start the truck .but if starter is faulty
or not connected properly then truck will not start.
4) The other thing to
check in this case is fuel in the truck .if there is fuel in the truck then
check the blockages in the fuel pump if the fuel pump looks proper then check
the fuel filter above the fuel pump.
5) If all the above
possibilities mentioned above checked out OK/perfect then its a electrical
issue and the wiring's in the truck needs to be
checked.the truck gets power from the
battery to get started.so the wires from battery needs to be checked one by
one.
Thanks. Keep updated for any more query. You can rate this
solution and show your appreciation.
My GMC Canyon does not
I don;t think anyone will have good answer here since all your signals comes thru computers. There is no fuse for this. Unless you have something else in the lighting system inadvertantly turned on then it is going to have to be diagnosed using a bidirectional scan tool. You should have a code stored in the body control module that will help in the direction your going to have to go.
Not finding what you are looking for?