2007 Ford Focus 2.0 - Answered Questions & Fixed issues

https://www.google.com/search?q=2007+Ford+Focus+speed+sensor+locations

Where is the 2007 ford focus speed sensor located?

Vehicle History https://www.vehiclehistory.com > questions > where-is... Located on the right side of the transmission near the output shaft. Like. (1). Leave your answer. 2 answers · Top answer: The 2007 Ford Focus speed sensor is found by watching: https://www.Youtube.com/watch?v=jxqItE9OI20 You will come into many issues with an engine. A gasket ...

2007 Ford Focus Sensor Locations

Rick's Free Auto Repair Advice https://ricksfreeautorepairadvice.com > 2007-ford-foc... Oct 3, 2018 - Wheel Speed Sensor (Left Rear) (Wagon) At left rear wheel. Wheel Speed Sensor (Left Rear) (3 Door) At left rear wheel. Wheel Speed Sensor (Left ...

http://m.focushacks.com/mod/Adjusting_Shifter_Linkage_without_the_special_tool Check it out.

Check for power at pin #16 of the OBD2 diagnostic connector under the dash in front of the driver, see illustration below of connector. Refer to the owners manual for fuse info if power is not present.

run the fault codes missing can be from problem injectors and low fuel pressure have a fuel pressure test done --should be in the 50.-65 psi range

Need diagram for 2007 ford focus fuse box. Samuel, Check the attached links,instruction and guides, Good luck "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." Ford Focus Fuse Box Location and Fuse Diagram Legend 2004 2011 Interior Fuse Box Location 2005 2007 Ford Focus 2007 Ford Focus SES 2 0L 4... https://owner.ford.com/tools/account/how-tos/owner-manuals.html?pagename=Owner/Page/OwnerGuidePage

It's a problem with the Idle Air Control.

Ensure thermostat is installed right side up or it wont allow proper flow. If thermostat is correct other problems could be Air in cooling system, low coolant level, plugged rad internal, water pump failure,coolant flow valve stuck,internal engine combustion leak to cooling system. Auto Repair Diagnostics How to Diagnose Cooling System Problem

/D OFF Indicator The instrument cluster receives the O/D OFF indicator status from the PCM over the communication network. When the overdrive function is turned off, the PCM sends a command to the instrument cluster to turn on the O/D OFF indicator. When a powertrain concern exists, the O/D OFF indicator flashes amber and illuminates green when overdrive is selected off. What code ? you said solenoid A - P0750 SSA SSA Solenoid Circuit Failure SSA circuit failed to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during on-board diagnostic. No reverse gear (short) or no 4th gear (open). MIL on. Go To Pinpoint Test A . P0751 SSA SSA Functional Failure (Stuck Off) Mechanical or hydraulic failure of the shift solenoid. Not all gears present, MIL on. Refer to Diagnosis By Symptom . P0752 SSA SSA Functional Failure (Stuck On) Mechanical or hydraulic failure of the shift solenoid. Not all gears present, MIL on. Refer to Diagnosis By Symptom . P0753 SSA SSA Solenoid Circuit Failure SSA circuit failed to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during on-board diagnostic. No reverse gear (short) or no 4th gear (open). MIL off. Go To Pinpoint Test A . Could be a wiring problem . Did you check the solenoid A wiring circuit back to the PCM ?

Can be a failing coil pack if you can move the coil pack to a different cylinder and then see if the code changes if it moves to the cylinder you moved it to then replace the coil pack should take care of the issue

You have a bad switch or a bad blinker relay

VALVE COVERS CAN LEAK INTO THE COIL WELLS AND SHORT OUT THE COIL. BUY A NEW COIL AND INSURE THAT THE PLUG IS GOOD AND NO OIL IS IN THE COIL WELL.

Lots of time its the piston ring are worn or sticking i suject to lucas it very good aditif thats a cheap way to try to control your oil comsuption

if you write down your vin and go to a dealer parts department they should be able to tell what your after.

Hammer.. thats what i use.

check your vacuum hoses for (cracks or tears) air leak.

Usually there is a blockage in the tube or a venting problem.

It may be a evap system problem

check for shorting bulb contacts and wire problems.

What light?

replace the streering rack