20 Most Recent 2005 Ford Falcon - Page 9 Questions & Answers

Check to make sure all pulleys and brackets are tight. Look for wear and tension on belts. Look for alignment to make sure they haven't shifted out of intended location. Take the belt off and spin by hand all of the pulleys, pwr steering, alternator, A/C, water pump, tensioner and make sure none of them are defective.

leave the hood up and in the sun or use a fan and let it dry out if

We do not have this model in the USA so have no info on it. Sorry.

The radio code is normally the last 3 or 4 digits of the vehicle VIN alternatively you should find it in the vehicle user manual

1-5-3-6-2-4

For fuel pump relay and fuse location diagram,click the link below :----http://technoanswers.blogspot.in/2012/02/ford-fuel-pump-relay-and-fuse-location.html ---------This will help.Thanks.

if vechicle idle fine but cut out off when you accelerate, could have restricted stopped up fuel filter or faulty tps sensor if so you will see check engine light flashing.

This could be two different issues. For the dash light get the vehicle plugged into an OBD scanner or a diagnostic system to check for Trouble Codes. These will give clues as to what and where the issue could be. Comment below with them and I'l try to help explain them. Unless the problem is with the brake booster most traction control systems do not use a vacuum to operate it. It is usually a set of electronic sensors on the wheels that the ECU uses to monitor tyre grip. As I cannot look at the car myself for that hose you will need to get a good mechanic to look at it. The vacuum hose could go to many things like the EGR system, the Turbo (if fitted) or possibly to the transmission.

Only way to get the code is dealership or someone with a radio programmer aka auto scanner

Ford Windsor Torque Specs - Help Center - Summit Racing

https://help.summitracing.com > answers > detail > a_id Apr 11, 2018 - Main Cap Bolts, 60-70 ft.-lbs. ; Connecting Rod Bolts, 22-25 ft.-lbs. (40-45 ft.-lbs. for 289TP and Boss 302) ; Cylinder Head Bolts, 65-72 ft.-lbs ...

Bolt Torque Spec Chart for Ford Engines - Maine Mustang

http://mainemustang.com > 65-73 Mustang Data Ford Engine Bolt Torque Chart ; Main cap bolts, 60-70 ft-lbs ; Outer 2 bolts of main cap bolts, 35-40 ft-lbs.(for 4 bolt main bearing caps only ) ; Connecting rod ...

5.0 HO Engine Bolt Torque Specs - Foxstang.com

https://www.foxstang.com > 5-0-ho-torque-specs Feb 21, 2020 - 5.0 HO (302) Head Torque Specs · Step 1: 23-35 FT/LBS · Step 2: 45-55 FT/LBS · Step 3: Additional 90 degrees (or 75-85 FT/LBS) · Use tightening ...

Immobilizer bypass trick Real not fake

Try and lock up the vehicle withe the key fob. Leave for 20 minutes and until lock with the key fob and try to start in usual way.

limited info generic answer ----if wiring request is for the vehicle [chassie etc]look up a repair manual for the van---if for the rv try dealer --rv shops --online forums --using the sub-model [rv model series ]

This will sound a bit silly and obvious but have you tried a new battery in the transponder key? Sometimes the fix is that easy. Have you had the vehicle plugged into an OBD scanner or a diagnostic system? Dashboard codes are commonly a bit vague about what the issue is. A Code 24 simply comes up as 'an Immobiliser issue' and thats all you get. The OBD scan will also tell you if there are any other issues with any of the other sensors on the engine. Comment below with any trouble codes you get and I'll try to help you more.

If it is the original radio, contact your Ford dealership with the VIN and they should be able to help you out.

Contact your Ford dealer.

Exactly which bolts do you need the torque settings for? Not all nuts and bolts are the same torque setting on a vehicle. I would recommend you buy a good workshop manual for your vehicle as that should list all the settings you need.

According to this yes it does. https://www.google.com/search?q=2000+ford+taurus+se+pats+module ..

Those are all lean codes. I would verrify that you have proper fuel pressure at the rail. If so, I would look for a vaccum leak.

https://www.justanswer.com/ford/1sbde-need-fuse-box-diagram-97-mustang.html https://www.startmycar.com/us/ford/mustang/info/fusebox/1997