20 Most Recent 2005 Ford Escape XLS Questions & Answers

Rusty or loose connection on one of the door switches...

On the valve cover

Hello, Unless you have to keep filling your cooling system, a small amount of water coming out of your muffler pipe is common. It is condensation created when your engine burns the moisture in the air. Some engines create a lot of condensation, others not so much.

I would think it is the master switch assembly on the drivers door.

Alignment

you have to take it back to the shop to have to have them look at it.. there is something they over looked. and call your insurance.

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?fromSearchPage=true&pageId=0996b43f802e6c08&partName=Ignition+Coils&partId=0996b43f802e6c08 Here you are.

https://www.google.com/search?q=FORD+ESCAPE+PCM+WIRING+FOR+MIDDLE+HARNESS or take a subscription to www.alldata.com Fuse 11 is MAF on some years, but not all https://www.google.com/search?q=FORD+ESCAPE+Fuse+%2311+keeps+blowing This is the fuse box for 2010, change to your year in the URL and press enter https://www.startmycar.com/ca/ford/escape/info/fusebox/2010 ..

Hi, Please first reference the cars manual for the removal process. Then, if need more help, please search for relevant youtube tutorial. And if still need further help, please consult a local mobile mechanic. Thank you.

no country told this is a world wide forum, and cars are not the same world wide at all, vast differences. (by laws too) quesiton #2 is this car fitted out with DRL, daylite running lamps>?????????? well fuses are first. check them first we do. then scan the PCM using scan tool (obd2 ,2008 or newer tools)\ USA answer? the PCM will tell you why, the owners guide ,in glove box see chapter fuses/ see head lamps? HL :? fuses,??? OOPS NO FUSES !!! focus , not focus Electric or Focus RS car,. right. the BCM runs the lamps and has no fuse for any pair of lamps it uses electronic regulators to NOT need fuses. 2018 auto lamps. the left and right bcm lamp drivers are not he same driver. so only one side fails. see? F74 fuse blow kills them all up front. 10 lamps dead. so is not this. here is my guess, manual lamps fail low beams. both lamps are bad. or wires cut or shored to them. but no wire can do that, there are redundant wired sides, so both can;t fail by DESIGN \even 2 grounds, left and right not the same. so learn the scan this car every time if fails fore sure now. or test the lamps 1 by1 , unplug them and see if low beams read 0 ohms if not the element it burned out. on both. scan it and see , left right dead lamps low/??????????

well the tranny service manual covers that but first we need the real transmission name and is it 4wd? well TCC is always 3 place. the outside controller (PCM/TCM) and wire there to . the transmission TCC solenoid.(inside) so I will now answer for the tranny guts. the TC clutch can be bad too, or the piston that drives it. or solenoid (dc volt coil to fluid valve solenoid) Ford box CD4E The Torque Converter Clutch solenoid is part of the solenoid valve body assembly. The solenoid valve body assembly is 142 (labeled Body assembly - transmission control solenoid (TCS)) on the Disassembled View on your Service DVD.(or manual) buy the manual or read this. (keep in mind it can just be a TC clutch bad and no the ACTUAL TRANNY AT ALL, OR TCM IS IN LIMPMODE, NO DTC ERRORS POSTED WHY NOT? $16 BUCKS TOO MUCH https://www.ebay.com/sch/i.html?_from=R40&_nkw=ford+cd4e++ATSG&_sacat=0&_sop=15 ALL YOu can do is (tell all DTCs thrown) and test for voltage on the tranny connector for TCC lock. and if is good you can put in ID 141 part. if fails install a new clutch.(main TC) 141 is the solenoid set, (all in one)

Take it to a Ford main dealer for conformation.

The most common cause of this is the electric in fuel tank fuel pump is sticking due to the introduction of the cold fuel. I would replace the pump.

Check OBD codes for a clue.

https://www.2carpros.com/questions/torque-specs-1035067 says; OHV 3.0 engine, my info says 54--64 ft lbs. So if you get right in the middle, should be fine. https://www.google.com/search?q=%22Ford+Escape%22+Torque+for+flywheel+bolts ..