20 Most Recent 2006 BMW M6 Coupe Questions & Answers


Have you checked your fuses ? Might also want to begin checking for power from the fuse panel to the light assembly.

BMW M6 Cars &... | Answered on Nov 30, 2016


Hi, you need to explain the problem your having a bit in order for us to help you. Please describe your problem in detail so we will be able to assist.

BMW M6 Cars &... | Answered on Apr 01, 2011


On the newer model cars they have started putting the battery under a myriad of plastic covers to make the engine compartment look cleaner. The "+" post that you have found is directly connect to the positive terminal on the battery. Put the positive cable on that post and then the negative on a bare bolt that is connected to the frame of the car, I would use the one on the sway bar if possible.

BMW M6 Cars &... | Answered on Mar 14, 2011


remember this is not a warning about oil level, that is another system, this is the engine oil pressure warning, this means the oil pressure being read by the oil pressure sending unit is below about 5-10 pounds per square inch or PSI, at this low of pressure the engine bearings can be damaged as well as other components like the valve train parts, the thing to do here is have the oil pressure tested by a shop with a special calibrated mechanical test gauge, the one in the car is electronic, u may just have a defective oil pressure sending unit, but take no chances, if the pressure is really low engine damage will occur soon, get the oil pressure PSI checked ASAP, if it is ok then the shop will replace the oil pressure sending unit on the engine, about a $100 part.

BMW M6 Cars &... | Answered on Feb 17, 2010


THEN FIX THE FUEL PUMP PROBLEM WE CAN NOT DO IT FOR YOU

BMW Cars &... | Answered on May 15, 2019


Special tool from BMW works through the transmission oil pan, you can't buy the tool so BMW dealer is the only place to go.

BMW Cars &... | Answered on May 14, 2019


On any engine you should find timing marks on the end of camshaft which line up with Mark on the crankshaft. TDC is top dead center which is when the first most piston is on it's compression stroke. When you move the crank to TDC the firstmost or number one piston will be on the compression stroke. Turning the camshaft to align with the timing mark on crankshaft will put the engine in proper valve timing.

BMW Cars &... | Answered on May 12, 2019


Remove the rear seat and reach into the truck and use the manual cable release, usually a brightly colored handle near the rear or sides of trunk.

BMW Cars &... | Answered on May 05, 2019


IN THE VIN # OR ON THE DRIVERS SIDE, DOOR JAMB THE MANUFACTURERS PLATE

BMW Cars &... | Answered on May 04, 2019


say service manual

BMW Cars &... | Answered on May 04, 2019


- 2EF7
2EF7 characteristic diagram thermostat, control
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
timeout

BMW Cars &... | Answered on May 04, 2019

Not finding what you are looking for?
2006 BMW M6 Coupe Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2009 BMW M6
2009 BMW M6

-2 Questions

2007 BMW M6 Coupe
2007 BMW M6 Coupe

-1 Questions

2006 BMW M6
2006 BMW M6

5 Questions

Top BMW Experts

stephen Kiarie
stephen Kiarie

Level 1 Expert

32 Answers

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1175 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

M6 BMW

  • M6 BMW

Most Popular Question

vibrating bmw m6

  • Cars & Trucks
Loading...