20 Most Recent
2003 Ford F-150 - Page 2 Questions & Answers
Radio and CD-6 player
The humming sound prior to cutting out could indicate a short in the unit itself.....remove unit and have it tested!
03 F150 club cab
The locks are controlled by the BCM(body control module). FOB and button. Check fuses. There are 2 to 4 fuses for the BCM. You have to have an owners manual to find the fuses. After that you have to start chasing wires and have a scanner to read the BCM. As far as the key. Did it work before? Or did you buy the truck used from a lot? Most used car lots will replace an ignition key, but won't spend the time or money to make sure the key will work in the door lock.
2003 f 150 transmission overdrive fuse
The problem is that either the wiring harness going to the overdrive control motor has chafed and is shorting out, or the overdrive control motor is bad. Check out the wiring harness VERY carefully, if it's OK replace the control motor.
1992 Ford F-150, What tools are required to replace front seal please.
Question edited for clarity and toss in some CAPS.
Question moved to model category.
Your vehicle is full of 'front seals'.
Wheel bearing seals.
Brake caliper seals.
Front transmission seal.
Plus a load of engine seals.
At minimum, a full socket set, a full set of open ended and ring, wrenches and a seal pick. Probably circlip pliers.
Google
1992 Ford F-150 replace (which one) seal
and watch the videos.
1995 Ford F-150. I just replaced battery and alternator but battery is completely dead when I turn engine over.
Question edited for clarity, typos and words that are incorrect 'automator' to 'alternator'.
Question moved to model category.
Put a battery charger on it for at least 8 hours on 6 amp charge. Make sure the battery ground has a good contact using a digital multimeter. After 8 hours, start the car and run it.
Next day, try and start again. If the battery is flat, you have parasitic draw.
https://www.fixya.com/cars/r29903527-parasitic_draw_car_batteries
One further thought, does this old vehicle have a security system and engine immobilizer? Do you have a steady or flashing red light anywhere. You may be locked out of starting the engine because you disconnected the battery. In fact Goggle says it does have anti-theft.
1995 f150 theft light flashing, cannot start!
Ford-Trucks.com
https://www.ford-trucks.com > forums > 1190498-199...
Sep 18, 2012 - Driver's door is unlocked by pressing the UNLOCK button of a remote entry transmitter. Two minutes and 45 seconds after the system has been ...
Dashboard Theft indicator. Anybody knows how it works?
May 27, 2010
HELP!! Im stuck!! How to reset antitheft on 96 f350
Dec 6, 2012
How to remove anti-theft 95 F150? - Ford Truck Enthusiasts
Jun 18, 2005
1995 F-150 Ignition/Alarm Problem - Ford Truck Enthusiasts
Aug 27, 2018
More results from www.ford-trucks.com
It's easier than you might think. In most cases, the anti-theft system on a Ford F-150 can be reset by turning the vehicle to "accessory" mode and leaving the key in the ignition for several minutes until the anti-theft light shuts off.
Feb 10, 2021
..
Why is my 1999 Ford F-150 V8 still running very rough?
Seafoam is for removing carbon deposits on 2 Stroke engines.
Fuel pumps either work or they don't. They don't 'almost work' and cause an engine to run rough.
You are subscribing to the 'let's try replacing this' method of car repair. It doesn't work and is expensive. You can't guess that maybe the O2 sensors are faulty. You diagnose the DTC trouble codes using a scan tool. That will tell you the state of sensors. If you want the WHOLE story, you buy a $3.5k scan tool computer or call a mobile auto electrician.
Things you can try for free. Clean the Throttle Body and MAF, clean the IAC (idle air control).
1999 Ford F-150 V8. Any thoughts why running so rough?
Question edited for clarity. All coded have a capital 'P' and 4 numbers, but you only had 3 so I added a zero ' P0171 and P0174'.
Question also moved to the model category.
Raja Akhter is an AI Auto Answer Bot, but it actually has a few good ideas for you. In addition I would remove and clean both sides of the throttle body and also clean the MAF (mass air flow sensor). I would also run a couple of bottles of Fuel System Cleaner through the injection system as all your codes are fuel air ratio based.
https://www.google.com/search?q=Fuel+system+cleaner
..
Not finding what you are looking for?