2007 Dodge Nitro - Answered Questions & Fixed issues

Question edited for clarity. Question moved to the sub category. All in the link. https://www.google.com/search?q=2007+Dodge+Nitro+firing+order ..

heater door actuator bad. it is up under dash on the drivers side towards the center.

https://www.nitroforumz.com/threads/nitro-still-not-starting-after-a-visit-to-the-specialist.41749/

The computer does it for you

Means something is wrong

What # fuse's J5 25amp , J4 25amp , M 30 15amp , M13 20amp M33 10amp . All these fuse's are power supply's for door modules and to the wiper / washer switch . The washer pump is controlled by the totally integrated power module . I suggest you google TIPM - dodge totally integrated power module . Chrysler , Dodge , Jeep all use this componet . Also watch youtube videos on finding a automotive electrical short . That's what you have a direct short to ground on those power supply circuits

If you reversed poles on the battery. You need to have it scanned. See which ones read. If none read, then you have to start disconnecting them one at a time till some thing reads. This is a problem that one computer has shorted. It shorted to the data lines.

Nacho, Coils are not normally replaced when changing spark plugs. Use the factory recommended plugs(OEM) . Check the attached links,instruction and guides, Good luck "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info." http://www.nitroforumz.com/threads/changing-spark-plugs.30635 Changing Nitro Plugs 3 7 4 0L how to change spark plugs in dodge nitro More Information for NGK 6987

If the fuse is ok, there may not be enough freon in the system to operate the safety pressure switches. 2007 Dodge Nitro Owners Manual Pdf

Measure all the fluid you drain and replace it with the same amount plus 1/4 quart.

Typically the electrical connection between the moving steering wheel and fixed steering column is the culprit. There are different names for this type of connector but it is usually in the form of some type of clock spring like device. You don't want to mess with it because you will be getting into airbag country. KABOOM! Dealer or skilled specialty automotive shop should replace.

2007 Dodge Nitro Recalls - Cars.com

www.cars.com/recalls/dodge/nitro/2007/
Cars.comLook up all NHTSA vehicle safety recalls for your 2007 Dodge Nitro, and contact ...THE TRANSFER CASE HEAT SHIELD MAY DROP DOWN AND RUB ON THE ...ADDITIONALLY, THE DRIVE SHAFT FAILURE WILL RESULT IN A LOSS OF ...

Differential and Transfer Case ' Dodge Nitro Forum

www.nitroforumz.com > ... > Detailing and General Maintenance Forum
Jul 24, 2010 - Vehicle: 2007 Nitro 4X4. Trim: SLT. Color: Black. Found this while searching for instructions on Front/Rear Axle and Transfer case fluid changes ... transfer case leak Aug 21, 2014 Front Axle CV Joint Nov 24, 2013 Leaky Transfer Case Oct 4, 2011 More results from www.nitroforumz.com images for 2007 Dodge Nitro Transfer case problems

recharge it for it to kik on

The metal tube from the intake going behind the engine is going to the EGR Valve. http://www.allpar.com/images/engines/4-V6-2.jpg

Owner's manual? no manual try manualslib.com

Where is the ECT Sensor located on dodge 2007 nitro Google Search click on link...do blow up the picture,click on that picture

Ignition switch....then the manufacturer specific codes have to be cleared by a high end tech or dealer, your harbor freight tool won't do it

If your vehicle with a Nitro engine is not upshifting and you're getting a P0750 code, it indicates that there is a problem with the shift solenoid "A". This solenoid is responsible for controlling the hydraulic pressure inside the transmission that helps to activate the clutches and bands that are responsible for shifting gears. There are a few reasons why the shift solenoid "A" may not be functioning properly, which could lead to the transmission not upshifting. These reasons include:

1. Malfunctioning Shift Solenoid "A": The shift solenoid "A" could be faulty, stuck, or damaged, preventing it from functioning properly.
2. Wiring Issues: There could be issues with the wiring or connections leading to the shift solenoid "A," which could cause it to malfunction.
3. Low Transmission Fluid: If the transmission fluid is low or dirty, it could prevent the shift solenoid "A" from functioning properly, causing the transmission to not upshift.
4. Internal Transmission Problems: There could be internal problems within the transmission, such as a clogged valve body, damaged transmission bands, or worn clutches, which could cause the shift solenoid "A" to malfunction.

It is recommended to take your vehicle to a certified mechanic or dealership to diagnose and repair the issue, as transmission issues can be complex and require specialized knowledge and equipment to fix properly.

Likely inside fuel tank

You need to have the BCM (body control module) scanned for faults. This requires a dealer level tool.