Top 20 2013 Toyota Highlander Questions & Answers

before you press the cd on button keep holding the eject button while you press power on, I know this works for computers etc.

Bettr check muffler for any gasleak or oil. Its leading cause of carfire

If you don't have any recalls on that vehicle go straight to the dealer. WARRANTY! The car is probably not recognizing your key if the key is fine it's the car causing the problem (body control module) do you have any type of security systems not working properly? If not DEALER, their problem.

under the dash where the fan is

When you removed the battery, your Highlander decided it was being stolen. After the new battery was installed, the vehicle can't confirm you are the owner using your key. It is all part of the anti-theft provisions.

Check this link out.https://www.justanswer.com/toyota/bey0x-2016-toyota-highlander-need-remove-rear-deck.html

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

Get a new radio to fix that . A dealer might be able to arrange a repair , but usually replace .

https://www.autocodes.com/c1201_toyota.html ` https://share.qclt.com/%E4%B8%B0%E7%94%B0Toyota%20RAV4%20Repair%20Manual/Brake%20Control/Vehicle%20Stability%20Control%20System/0370025.pdf

with the help of service and repair manual you can solve your problem and you will get the manual from the given link http://toolsnyou.com/

PROCEDURE. Make SURE the battery you installed is good.

• Driver's door open, key removed from ignition switch
• Within 5 seconds: Insert and remove the key from the ignition switch twice
• Within 40 seconds: Close and open driver's door twice
• Insert and remove the key from the ignition switch. Close and open driver's door twice
• Insert the key into the ignition switch and close the driver's door
• Within 40 seconds: Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program and remote transmitter code whilst erasing the original codes. Three times to check how many remote transmitter are currently registered or five times to erase all registered codes
• Remove key from ignition switch. System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered
• Within 40 seconds: Press and hold LOCK and UNLOCK buttons simultaneously for 1.5 seconds
• Within 3 seconds: Press LOCK button
• SYstem should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed
• Within 40 seconds: Repeat button procedure to program remaining remote transmitters.
• NOTE: To exit programming mode: Open driver's dorr
• NOTE: A maximum of 4 remote transmitters can be programmed

If the above programming procedures do not work, then you should contact your locksmith. Goood Luck!

There's a button on the glove box toward the center console, try turning it off and see what happens.

I recently tried the DIY service and repair manuals from a website and it actually helped me repair transmission problem in my jcb 3cx site-master. It would'nt move forward or reverse, engine was good both solenoids for forward and reverse worked, but still couldn't diagnose the problem. I don't have much technical knowledge but I just followed it step-wise, and now it works perfect! covers wiring, diagrams, torque specs, PCV, everything got it from www.reliable-store.com

Change your mounting engine with the new one

Assuming you have a dual climate control system, the blend door actuator for the passenger side has stopped working and would need to be replaced

-Slide the child safety to other direction and try open again. -If not then try the other way. Good luck Mai

hope this will work.. https://www.ebay.com/itm/04-05-06-07-TOYOTA-HIGHLANDER-OVERHEAD-OVER-HEAD-CONSOLE-CONTROL-UNIT-OC875/401236003963?fits=Make%3AToyota%7CModel%3AHighlander&hash=item5d6b878c7b:g:WkAAAOSwI59aC6B5

The inverter caused a short circuit , the insulation on the lighter socket is earthed out or a cable is burnt and earthed out , disconnect the lighter cable, and check if shorted , if not work back to the ignition switch till you find it.

Remove the display and have it rebuilt or replace new, cost new around $3500.00