20 Most Recent 2012 GMC Acadia Questions & Answers

In this link https://portal-diagnostov.com/en/2020/04/13/power-mirrors-gmc-acadia-sle-2011-system-wiring-diagrams/ ..

For issues like this you need an auto electrician with a pro grade bi-directional scan tool computer to diagnose. The misfire may just be spark plug condition, but it could be a sensor issue. It is better to pay a pro and only change the parts that need it rather than 'let's try replacing this' method of repair.

A 2010 Acadia has GM PasskeyIII security. It requires a transponder key programmed to operate with the vehicle. Your "plain key" must have a transponder encased in the plastic head of the key and was programmed to work with your vehicle.

The random no crank is likely because the immobilizer is sometimes unable to validate your key. Could be the key or a problem with transceiver in the ignition lock assembly.

If you have a second key and it has the same issue then the problem is not likely the keys but with the transceiver.

Engine off,ignition on, gas pedal to the floor 3 times.

what year and motor size

Could be low on refrigerant

Door Lock System Components The power door lock system consists of the following components: • Driver door module (DDM) • Passenger door module (PDM) • Door lock relay--Located in the instrument panel (I/P) fuse block and controls the locking of the rear doors. • Door unlock relay--Located in the I/P fuse block and controls the unlocking of the rear doors • Body control module (BCM) • IP BEC • Reversible door lock actuators in each door Driver and Passenger Lock System Operation The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two-position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitor these inputs and send a LAN message indicating a change in the switch position. Modules, that activate the power door lock motors, receive the LAN message and activate the motor in the appropriate direction to lock or unlock the vehicle doors. The body control module (BCM) upon receipt of a lock or unlock signal will control the rear door lock or unlock relays and also send a LAN message to the DDM and PDM to perform the commanded function. The modules that activate the power door lock motors are: • DDM (driver door lock actuator) • PDM (passenger front door lock actuator) • BCM (both rear door lock actuators) The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other, causing the doors to lock or unlock. The rear passenger doors are controlled by the BCM through the rear door lock/unlock relay which is incorporated onto the printed circuit board in the LH BEC. The BCM controls the unlock relay by providing ground to energize the coil and controls the lock relay by providing battery voltage to energize the relay coil. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. Since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.

Everything you mention is in the same door. Look for a connector between the body and the actuators in the door. This may be accessible or just inside the door itself, past a rubber grommet. Pull the connector apart and inspect it. Spray with silicon or WD40 and reassemble.

DTC P0497: Evaporative Emission (EVAP) System No Flow During Purge Circuit/System Description The control module tests the evaporative emission (EVAP) system for a large leak, or a stuck closed EVAP canister purge valve. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge valve OPEN and the EVAP vent valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level increases too slowly, a DTC sets. Diagnostic Aids • A loose, missing, or damaged fuel fill cap can cause this DTC to set. • A stuck closed, blocked, or restricted EVAP canister purge solenoid valve, can cause this DTC to set. • A blockage or restriction in the EVAP canister purge solenoid valve vacuum supply hose, EVAP canister purge solenoid valve purge pipe, EVAP canister, or vapor pipe, can cause this DTC to set. • A temporary blockage in the EVAP canister purge solenoid valve, purge pipe or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system. • To help locate intermittent leaks, use the J 41413-200 Evaporative Emissions System Tester (EEST) to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT High Intensity White Light. Introducing smoke in 15 second intervals will allow less pressure into the EVAP system. When the system is less pressurized, the smoke will sometimes escape in a more condensed manner. • To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT . • Observe the Freeze Frame/Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set. This may assist in diagnosing the condition.

Is it the Bendix? Is your alternator working? Is your fuel pump working correctly. It could be a few things, just troal and error. Good luck.

A good scan tool can unlock the radio.

https://www.yourmechanic.com/article/p2099-obd-ii-trouble-code-post-catalyst-fuel-trim-system-too-rich-bank-2-by-andrew-quinn

usually the underneath connector is just loose .try to remove the connector and clean .if the same problem occurs check the for the ground and blown up fuse

On most vehicles there are 3 blinker bulbs on each side. One at the front corner, one at the rear corner and a third side repeater usually mounted in the front wing, (fender). Some more modern car companies have started fitting the side repeater into the door mounted 'wing' mirror body. The blink rate will usually be around 60 to 120 flashes per minute. If the rate on yours is usually slower, a higher speed flash suggests there is a blown or missing bulb.

DTC P0877: Transmission Fluid Pressure (TFP) Switch 4 Circuit Low Voltage The transmission fluid pressure (TFP) switch 4 is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The TCM supplies 12 volts to the TFP switch 4 on the TFP switch 4 signal circuit; the TFP switch 4 has an internal case ground. TFP switch 4 is normally closed, Low. When oil pressure is present at the TFP switch 4, the switch is open, high. The normally low clutch pressure control (PC) solenoid 4-5 controls the transmission fluid to the 1-2-3-4 clutch. The TCM monitors the normally closed TFP switch 4 signal circuit to determine the 1-2-3-4 clutch status. P0877 The TCM detects that the TFP switch 4 signal voltage remains low, 0 volts when the 1-2-3-4 clutch is commanded ON for 5.5 seconds or greater. Action Taken When the DTC Sets • DTCs P0877 and P0878 are Type C DTCs. • The TCM freezes transmission adaptive functions. Circuit/System Testing Ensure the TFT is near the temperature displayed in the Failure Records. Start the engine and place the transmission range selector in D6. Observe the TFP switch 4 parameter while commanding 4th gear and then commanding 5th gear with the scan tool. The TFP Switch 4 should transition from High in 4th gear to Low in 5th gear. ? If the TFP switch 4 parameter state does not change, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection . ? If no concerns are found, replace the control solenoid (w/body and TCM) valve assembly. Component Testing Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection . Repair Instructions Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Control solenoid (w/body and TCM) valve assembly replacement - refer to Control Module References for replacement, setup, and programming. Perform the Service Fast Learn Adapts

My personal suggestion would be to go for these repair catalogs. I know this website www.reliable-store that i used to buy them from, and they sold online it was very good manual. Go ahead, I bet.

There should be a lever at the base which allows the seat to fold forward then a secondary latch unlocks the pivot to allow removal. If you need further help, reach me via phone at https://www.6ya.com/expert/james_8f14c50d9c6cdea8

Fuel injector cleaner

Replace the passenger side blend door actuator