Nissan Cars & Trucks - Page 7 - Recent Questions, Troubleshooting & Support

bank two is the bank of cylinders that is closer to the radiator...not the firewall side.

Hi, this cars cam sensors are easy to change. One on the right side and one on the left side of the motor.

• See my diagram for a visual

1. Remove the mounting bolt.
2. Remover the connector
3. Remove the sensor
4. Install new sensor.
5. Reverse to complete.
6. Same for the sensor on the other side.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

Could be the sensors or the solenoid switch in the transmission.I recomend it goes to an automatic transmission specialist for repair.

https://www.nissanpartsdeal.com/parts-list/1986-nissan-720_pickup/body_electrical/wiring.html

I found this info.

P0047 Turbo/Supercharger Boost Control A Circuit Low Read more at: https://www.obd-codes.com/p0047

I have never heard of a DTC Code referred to as 'Problem 0047', as it is normally written as P0047. I wonder if the P does stand for Problem? Quick check and No it doesn't P Codes - P stands for powertrain, meaning the issue is related to engine functions, transmission, or drivetrain. C Codes- C codes cover chassis functions such as steering, suspension, and brakes. Here is a link for your code P0047. https://www.google.com/search?q=Nissan+frontier+shows+P0047 ..

Definition of check engine code P0047: Generic (Common for all car manufacturers): Turbocharger/Supercharger Boost Control "A" Circuit Low

P0072 Ambient Air Temperature Sensor Circuit Low Read more at: https://www.obd-codes.com/p0072

P259A Engine Code Repair - P259A OBD-II Diagnostic ...

enginecoderepair.com http://p259a.enginecoderepair.com The reason of P259A OBD-II Engine Trouble Code is O2 Sensor Heater Circuit Malfunction. P259A DTC reports a sensor fault, replacement of the sensor is unlikely ... ..

https://www.youcanic.com/nissan-transmission-problems/

Question edited for clarity. Question moved to model category. Videos

6. CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 1. Disconnect ECM harness connector. 2. Check harness continuity between ECM terminal 14 and CKP sensor (POS) terminal 2.continuity should exist. Refer to Wiring Diagram. 3. Also check harness for short to ground and short to power. OK or NG OK >> GO TO 7. NG >> Repair open circuit or short to ground or short to power in harness or connectors. 7. CHECK CRANKSHAFT POSITION SENSOR (POS) Refer to EC-326, "Component Inspection" . OK or NG OK >> GO TO 8. NG >> Replace crankshaft position sensor (POS). 8. CHECK GEAR TOOTH Visually check for chipping signal plate gear tooth. OK or NG OK >> GO TO 9. NG >> Replace the signal plate. 9. CHECK INTERMITTENT INCIDENT Refer to EC-147, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT" . >> INSPECTION END Component Inspection UBS002UJ CRANKSHAFT POSITION SENSOR (POS) 1. Loosen the fixing bolt of the sensor. 2. Disconnect crankshaft position sensor (POS) harness connector. 3. Remove the sensor. 4. Visually check the sensor for chipping.

If you have water in the tank you will also have corrosion or rust. Drop the tank and dispose of the contents in an approved mannor; NOT down a drain!! Check for any rust damage and if not too severe reuse the tank. Clear the 'wet fuel' from the system by disconnecting all of the feed pipes and hope the pump has not been damaged by lack of lubrication from the water. Remove the injector feed pipes and allow to drain. Reassemble all but the injector feeds to allow for bleeding the system, refil with fuel, cycle the ignition key to fill the system with fuel and when fuel sprays from the injector feed, reconnect the injector and attempt to start the engine. Good luck.

https://www.titantalk.com/threads/heater-fan-not-working-help.191170/ This site will give you a few ideas on what to look for.

https://gearfixes.com/nissan-rogue-door-lock-problem/ This article may help you solve your problem.

I would like to know the answer to this as well

Question edited for clarity. Question moved to model category. There are some diagrams here, but not very clear. https://www.google.com/search?q=nissan+pathfinder+brake+booster+hose+diagram Service Manuals https://www.google.com/search?q=nissan+pathfinder+brake+booster+hose+diagram ..

Your 2012 Nissan Frontier's fuel filter is located inside the fuel tank, so it's part of the fuel pump housing. There is no external fuel filter for you to replace

I would look for 12volt supply to the port. Possible blown fuse.