Mitsubishi Eclipse - Recent Questions, Troubleshooting & Support

Its underneath the motor on the left side. Kinda hard to get to.

Question edited for clarity. Question moved to model category. https://www.google.com/search?q=2001+mitsubishi+eclipse+stereo+wiring+diagram ..

Question edited for clarity. Question moved to model category. https://portal-diagnostov.com/en/2020/04/20/power-windows-mitsubishi-eclipse-spyder-gt-2003-system-wiring-diagrams/ https://www.google.com/search?q=2003+Mitsubishi+Eclipse+2.4.+Master+window+switch+wiring+diagram ..

I'm sorry to hear that you're having trouble with your 1989 Mitsubishi Eclipse. Here are a few things that you can check to try to get spark to the spark plugs: Check the spark plug wires: The spark plug wires can become damaged over time, which can prevent spark from reaching the spark plugs. Inspect the spark plug wires for any cracks or breaks. If you find any damage, replace the spark plug wires. Check the spark plugs: The spark plugs can also become fouled or damaged over time, which can prevent spark from reaching the spark plugs. Remove the spark plugs and inspect them for any damage. If you find any damage, replace the spark plugs. Check the ignition coil: The ignition coil is responsible for generating the spark that ignites the fuel in the engine. If the ignition coil is faulty, it can prevent spark from reaching the spark plugs. Inspect the ignition coil for any damage or signs of wear. If you find any damage, replace the ignition coil. Check the distributor cap and rotor: The distributor cap and rotor are responsible for distributing the spark from the ignition coil to the spark plugs. If the distributor cap or rotor is faulty, it can prevent spark from reaching the spark plugs. Inspect the distributor cap and rotor for any damage or signs of wear. If you find any damage, replace the distributor cap and rotor. If you have checked all of these things and you are still not getting spark to the spark plugs, it is possible that there is a problem with the engine's computer. In this case, it is best to take the vehicle to a qualified mechanic for diagnosis and repair. Here are some tips to help prevent these problems from happening in the future: Change your spark plugs and spark plug wires according to the manufacturer's recommendations. Keep your engine clean and well-maintained. Avoid running your vehicle on low fuel. If you notice any problems with your vehicle's performance, have it checked out by a qualified mechanic as soon as possible.

Do you have the 4G37 or 4G63A or 4G63T? if you don't know.. that basically means do you have a 1.8, 2.0 SOHC, 2.0 DOHC, or a turbo-charged engine? I have an '05 Evo and i small screw on the throttle-body near where the intake connects to it. If you turn it it changes how high the engine will rev while its idleing. I'm not sure if thats what you mean because if not you may have to take it to a shop and get it recalibrated.

Question edited for clarity, add maker, get rid of abbreviations. Question moved to model category. Did you disconnect the battery? Did you reset security and immobilizer? Did you Calibrate it? https://www.google.com/search?q=1992+Mitsubishi+Eclipse+1.8.+How+to+install+Throttle+Position+Sensor

Question edited for clarity and funky spelling of the maker. It is written on the car, don't you see it every time you drive :>D Cigar lighter (power outlet) fuse in the Mitsubishi Eclipse is the fuse #16 (Power Outlet) in the Instrument panel fuse box. Fuse 23 for windows.

Fuse Box Diagram Mitsubishi Eclipse (4G; 2006-2012)

Fuse-Box.info https://fuse-box.info > mitsubishi > mitsubishi-eclipse-... The fuse box is located on the driver's side of the instrument panel, behind the cover. The location of the fuses in the passenger compartment: Mitsubishi ...

no dtc codes posted zero joy. we can't just guess them. ok? the TCM sees errors and can not shift or TCM sees engine problems that prevent upshifts. not told a real problem (beside codes vague) PRNDL so tranny fails in all gears R and D and L????? or only is dead in Drive???? or will not upshift from 1,2,3,4,??? or flares (false neutrals) at 2nd gear or others? or stuck in 2nd gear.?(in drive) car is DIP,dead in the Pavement.? tell all the engine does and tranny good and bad. both there are list of on car checks.

1. fuse good. all.
2. level good hot and filter in box not missing, never overfill any A/t box. or foams up and fails hard.
3. scans show DTC codes, all matter post them.
4. tranny linkage not bad or not adjusted correctly
5. last test is tranny pump pressure port tests with hand gauge 300psi) in PRNDL all selections per the service manual.
6. no bad wring from TCM (PCM) to tranny. or there connectors. rusted.

Question edited to add maker and for typos. Question moved to model category. You swapped out a lot of components. Did you address the P0403 malfunction code? There is lots on it in this link. Also it could be a wiring issue to it. https://www.google.com/search?q=2000+Mitsubishi+Eclipse+P0403.. ..

Hi there,

Diagnostic codes # P0115 to P0119 all relate to the ECT (Engine Coolant Temp) sensor circuit.

Assuming you have correctly diagnosed a faulty ECT sensor, here are the instructions to locate and test:

* Look for a bolt size sensor with a wire attached - on Mitsubishis, the ECT sensor is usually located either on the Intake Manifold, or close to the Thermostat housing (to measuer coolant temp).

This is what is looks like:


* To test the ECT sensor:

* With the sensor portion immersed in hot water, check resistance as per the table below (convert to degrees F if necessary):


* If the resistance is too far out of spec, then replace the sensor.


Cheers,


"Please take a moment to rate this solution with a 'testimonial' and/or 'thumbs up', as this will keep my status active and allow me to continue offering technical support. Thank you."

correct my did the same thing replace the switch

check out the videos https://www.google.com/search?q=2006+Mitsubishi+Eclipse+GS+How+to+install+serpentine+belt ..

Question edited for clarity. Question moved to Category. Torque and sequence https://www.2carpros.com/questions/rocker-arm-assembly-torque-specs Cam Belt Timing https://www.google.com/search?q=2003+Mitsubishi+Eclipse+GS.+Cam+belt+timing ..

You need to provide more information on what you need help with . If you are putting in an after market radio, you can get a wiring harness that will just plug into your radio harness and with the instructions you can wire this yourself. Usually simple. Go to a good parts house for parts and help.

It's in the tank, but you can get to it from the back seat. Brief instructions below--let me know if you want more details.

1. Properly relieve the fuel system pressure.
2. Disconnect the negative battery cable.
3. Remove the rear seat cushion, by pulling the seat stopper outward and lifting the lower cushion upward.
4. Remove the access cover.
5. Disconnect the fuel pump wiring.
6. Disconnect the return hose and the high pressure fuel hose.
7. Remove the pump mounting nuts and remove the pump assembly.

All in the link https://www.google.com/search?q=2007+Mitsubishi+Eclipse+timing+marks ..

google 2000 Mitsubishi eclipse fuel pump relay location for more info https://www.fixya.com/cars/t3177909-fuel_pump_relay_located_2000

Question edited for clarity and the correct name of the maker which is written on the rear of the trunk! :>D Question moved from Heating and Cooling to the correct Vehicle category of Mitsubishi Eclipse. Fuse 10 under the hood.

Mitsubishi Eclipse Underhood Fuse Diagram

https://blownfuse.co > mitsubishi > mitsubishi-eclipse-p... Fuse Number Description AMP Rating 1 Fuse (+B) MAIN BATTERY FUSE 80A 2 Radiator fan motor 30A 2.4 liter, 50A 3.8 liter 3 Anti?lock braking system 60A View 23 more rows

• Mitsubishi Eclipse Passenger Fuse Diagram

  https://blownfuse.co > mitsubishi > mitsubishi-eclipse-p... Feb 27, 2021 - Below is the passenger fuse diagram for the Mitsubishi Eclipse third-generation 2000, 2001, 2002, 2003, 2004, and 2005 model year.

the switches need cleaning ,they have contacts in them that get dirty you can spray contact cleaner on them or use emery paper to file them, they are not to hard to pull apart

If you need any kind of workshop service repair manual you can go for here big-manuals.comManuals