Jensen Hunter S FLM002 - Recent Questions, Troubleshooting & Support - Page 8


This usually occurs on the male side of the connectors - you are probably losing connection on at least one pin in one or or both of these connectors. Sometimes the offending pin(s) have been pushed back into the housing, are corroded or bent. It is a huge waste of time trying to adjust these - best bet is try a new cable.

Cars & Trucks | Answered Yesterday


Interior Lamps
The interior lighting consist of the following 2 groups. This first group includes lamps that may not be dimmed.
• The cargo lamp
• The dome lamps
• The reading lamps
• The vanity mirror lamps

Vanity Mirror Lamps
The inadvertent power courtesy lamps supply voltage circuit of the body control module (BCM) provides battery positive voltage to each vanity mirror lamp. When the vanity mirror cover on the sunshade is opened, a switch closes to provide a ground circuit and the vanity lamp illuminates.

Battery Rundown Protection/Inadvertent Power
The body control module (BCM) inadvertent power courtesy lamps supply voltage circuit provides battery positive voltage to all of the interior reading lamps and both visor vanity mirror lamps. In the event that any of these lamps were to remain illuminated for a period of more than 20 minutes with the ignition switch in the OFF position, the BCM will deactivate the inadvertent power courtesy lamps supply voltage circuit to prevent a total battery discharge condition. Only when the ignition switch is cycled back to the RUN position will the BCM reset the internal timer and reactivate the inadvertent power courtesy lamps supply voltage circuit.
The BCM also utilizes the inadvertent power courtesy lamps supply voltage circuit as a courtesy lamp request signal circuit when none of the lamps in the circuit are illuminated. When a lamp switch is activated, the BCM receives the request for lamp illumination and switches to supplying voltage to the inadvertent power courtesy lamps supply voltage circuit.


Just from reading this ,i wouldn't think this a fuse problem . The BCM has main fuse's for battery voltage supply . The light's your having problems with don't have a separate fuse .

Hooking up a factory or some other professional type scan tool an checking the BCM for DTC'S - diagnostic trouble code's is the first place i would start my diagnostic's .
DTC B1480
The body control module (BCM) supplies battery positive voltage to the reading lamps and both visor vanity mirror lamps. In the event that any of these lamps were to remain illuminated for more than 20 minutes with the ignition switch in the OFF position, the BCM will deactivate the inadvertent power courtesy lamps supply voltage circuit to prevent a total battery discharge condition.

Then follow the diagnostic procedure test's in the service repair manual .
Conditions for Running the DTC
The battery voltage must be between 9.0-16.0 volts.
Conditions for Setting the DTC
• The inadvertent power courtesy lamps supply voltage circuit to the reading lamps and both visor vanity mirror lamps is shorted to ground for more than 1 second.
• There is a loss of the rear fuse block TBC 4 battery supply voltage to the BCM for more than 1 second while one or more of the lamps in the inadvertent power circuit have been activated.

Connector End View Reference: Lighting Systems Connector End Views or Body Control System Connector End Views in Body Control System
1
Did you perform the Lighting System Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Lighting Systems
2
Inspect the TBC 4 fuse in the rear fuse block.
Is the fuse good?
Go to Step 4
Go to Step 3
3
Test the inadvertent power courtesy lamps supply voltage circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 5
4
Test the TBC 4 battery positive supply voltage circuit at the body wiring harness extension harness connector at the body control module (BCM) for battery voltage. Refer to Circuit Testing in Wiring Systems.
Is battery voltage present?
Go to Step 5
Go to Step 6
5
Inspect for poor connections at the harness connectors of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 8
6
Inspect for poor connections at the body wiring harness extension harness connectors. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 7
7
Replace the body wiring harness extension harness to the BCM. Refer to Body Control Module Body Wiring Harness Extension Harness Replacement in Body Control System.
Did you complete the replacement?
Go to Step 9
--
8
Important: Perform the setup procedure for the BCM.
Replace the BCM. Refer to Body Control Module Replacement in Body Control System.
Did you complete the replacement?
Go to Step 9
--
9
Use the scan tool in order to clear the DTCs.
Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?
Go to Step 2
System OK


Fuse Block - Rear
Beneath the left rear seat

Cars & Trucks | Answered Yesterday


I bet you would have great results for that on Google. But they usually get a dark center with a red ring around it. the longer the bite goes untreated the larger the dark canter gets and it will have a pale to grey area around it then the red ring. This is where the tissue is dying. My recommendation, if you think you have a recluse bite DO NOT HESITATE get to the Dr.

Cars & Trucks | Answered Yesterday


Use a dictionary .... it would help if we new on what. Instruction book .... computer screen ... online newspaper ... Sat Nav ... Car radio ...etc

Cars & Trucks | Answered 2 days ago


Thrombocytopenia is a condition in which you have a low blood platelet count.Platelets (thrombocytes) are colorless blood cells that help blood clot. Platelets stop bleeding by clumping and forming plugs in blood vessel injuries.

Cars & Trucks | Answered 2 days ago


firstly battery light comes on when altenator not charging in faulty condition but it comes ones when you switched to ignition on rest of all check the battery gravity and go for altenator repair job done

Cars & Trucks | Answered 2 days ago

Not finding what you are looking for?
Cars & Trucks Logo

-3 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jensen Experts

john h

Level 3 Expert

20352 Answers

Dan Hooper
Dan Hooper

Level 3 Expert

3212 Answers

Robert Wesighan
Robert Wesighan

Level 1 Expert

6 Answers

Are you a Jensen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jensen Cars & Trucks

  • Forum

View Most Popular

  • Jensen Cars & Trucks
Loading...