Jeep Wrangler - Popular Questions, Answers, Tips & Manuals


Check the power fuse to the computer. If the computer does not get power the engine light will not work. If the computer does not work it cannot ground the relay to the fuel pump.

Jeep Wrangler... | 39 views | 1 helpful votes


hello
u'd need a proper manual for this in my opinion
like there are plenty of dealers and online shops that deal in those..
you can get some free at reliable-store and it;s actually really illustrative

Jeep Wrangler... | 34 views | 0 helpful votes


Take your fob to a parts house and they have a fob tester to make sure it is not the fob.

2011 Jeep... | 28 views | 1 helpful votes


To clear the check engine light, take the positive battery terminal off for about 30 seconds. Re install and start it up. It should be off.

Jeep Wrangler... | 53 views | 0 helpful votes

Tip

How To Check The Intermediate Steering Shaft On a Jeep Wrangler


This video will show you how to check the intermediate steering shaft in your Jeep Wrangler. This procedure would also be the same in a Jeep CJ, YJ, TJ If your intermediate steering shaft is worn or loose, it should be replaced immediately so that it doesn't fail while driving your Jeep. If you are running oversize tires on you Jeep and the steering shaft is loose, it should be replaced immediately.

on Jan 02, 2019 | Jeep Wrangler Cars & Trucks


You may have a bad coolant temp sensor but the only way to prove it is took hook into scanner that can read data, also check the fuel pressure. Note if the ect is bad it will be reading -45 no matter what the temp is it will get better as the lazy sensor catches up. I hope this helps, Take care

Jeep Wrangler... | 20 views | 0 helpful votes


does this happen when using the remote to lock/unlock vehicle ? if so thats perfectly normal as long as it's only for about 15 seconds or so

Jeep Wrangler... | 37 views | 1 helpful votes


Go online and download an owners manual for the Jeep. It will give you the location of the fuse associated with your dash lights. Or you could start pulling fuses and looking for the one that is blown.

1989 Jeep... | 30 views | 0 helpful votes


http://ibb.co/gB5VWc

Are these your wire colors for headlamps? In the diagram, the top wires are voltage, the bottom wire is ground, check both. There is no fuse for headlamps. There is internal circuit breaker in headlamp switch. The exterior lamps not including headlamps are fuse protected.
Maybe a problem with bulb or wiring circuit. The voltage for hi beams on both sides, come from the same place. Lo beams, the samething.

1990 Jeep... | 818 views | 1 helpful votes


Sounds like an intermittent miss. Possible worn plug, bad wire, or an injector that is shorting out. Check to see if any codes are set. This will help you narrow the problem to a certain cylinder.

2002 Jeep... | 44 views | 0 helpful votes


The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring d iagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Jeep Wrangler... | 35 views | 0 helpful votes


You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs, PCV,
owner's/service/repair/parts/maintenance manuals etc everything
this website www.reliable-store.com
it's a very good website for vehicle problems even as old as 1991 ford..

2005 Jeep... | 353 views | 0 helpful votes


IAC was a good guess...

ALSO sounds more like a throttle position sensor...

(TPS is my GUESS... but it is your MONEY and
this EASTER-EGG hunting style trouble shooting
can typically cause MORE TROUBLES than fixing).

(( but still preferred over taking it to a "DEALER" )).

My BEST suggestion... Get your codes read...
and AVOID the pitfall of needlessly replacing
those rather expensive OXYGEN SENSORS
($$$$)...

Doesn't cost you a thing to bring those trouble
(DTC) codes back here and give us another
chance... (I'm just saying).

Look at the costs at ROCKAUTO... (great catalog)

Carnac the Magnificent

Jeep Wrangler... | 46 views | 0 helpful votes


When that code shows up, it normally means that the O2 sensor is bad, or there is a bad connection or burnt wire. All of which are corrected with replacement of the O2 sensor.

Jeep Wrangler... | 377 views | 0 helpful votes


I think you could use this manual method instead.. My nephew used it to repair my car and it's perfectly fine now. Here's the website
he bought it from. www.reliable-store.com

1999 Jeep... | 124 views | 0 helpful votes


sounds like the clutch is not disengaging to me. is it hydraulic?? needs fluid maybe?? has a leak??

1992 Jeep... | 271 views | 0 helpful votes

Not finding what you are looking for?

-3,437 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...