Honda Accord - Recent Questions, Troubleshooting & Support - Page 9

If a b14 code pops up on your Accord, you can fix it as follows: 1. Replace engine oil and filter 2. Check the tire pressure and rotate the tires 3. Check drive belt, install a new air cleaner element, and replace the dust and pollen filter 4. Replace the transmission fluid if required 5. Replace timing belt and spark plug if need be 6. Change the engine coolant 7. Also, replace the back differential fluid Note: if the problem gets resolved at step 1, you don't need to move forward with the rest of the steps.

you will need to pull radio out and retrieve s/n off of stereo. with s/n i can get anti theft code for you. if you need help with removing radio let me know.

Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

Your car’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
You should have received a card with your manual (if you have one) that lists your audio system’s code number and serial number. If you don't have the card, you can get the code number from your Honda dealer, but to do this, you will need the system’s serial number.
If your car’s battery is disconnected or goes dead, or the radio fuse is removed, the audio system will disable itself. If this happens, you will see ‘‘Code’’ in the frequency display the next time you turn on the system. Use the Preset buttons to enter the five-digit code. If it is entered correctly, the radio will start playing.
Hope this is helpful.

Did you check the starter out ?

Check battery connections with a meter.

I live in Seatac, Washington, the library has all the ELE schematic for most any cars, I just ask the person behind the counter, they will give or make you copy's with little to no charge, I have had to do this a few times on cars that I had have ELE probs with! Good luck! Tim L

check your trunk lock mechanism. it might not be locking properly and not seating right due to rear damage and trunk lights are on and that can drain the battery overnight. have it adjusted.

it sounds like your lock actuator inside the door is bad

Step 1 Remove the center console cover around the parking brake lever located inside the car between the driver's seat and the front passenger seat. Step 2 Turn the adjuster nut with your wrench or pliers located at the end of the parking brake cable rod, to loosen the adjuster nut. Make sure it doesn't come off the end of the parking brake cable rod. Step 3 Raise your Honda Accord rear wheels in the air using your jack and support both rear wheels with your jack stands. Step 4 Pull up on the parking brake handle for two notches or clicks. Tighten the adjuster nut until there is a slight resistance on the rear wheels when they are spun. Step 5 Release the parking brake lever. Verify the rear wheels do not have resistance and are able to spin freely. Step 6 Pull up on the parking brake lever three to five notches and verify the rear wheels do not turn at all. Lower your Honda Accord using the jack and remove the jack stands from the rear wheels. Items you will need

• Wrench or pliers
• Jack and jack stands

There is most likely dirt debris and junk of all sorts from the life of the vehicle that is gathered up in the clean the gears and locking mechanism of a seat belt a good pair of cleaning behind the cover should solve your problem

Take wires out of cigaret lighter , then replace fuse , if fuse stays ok without cigaret lighter connected then something shortning lighter inside.

When your vehicle is coming up for due maintenance, the light will flash for a few when you start the car. When the time for scheduled maintenance is due, the light will remain on constantly. It's just routine maintenance, but if you haven't done it, that's your reminder. Then, you or your mechanic will have to reset that maintenance reminder light.

- Faulty Cylinder Position Sensor - Cylinder Position Sensor harness is open or shorted - Cylinder Position Sensor circuit poor electrical connection try and replace the cylinder position sensor Read more: http://helpforcars.net/obd_codes/p1381_honda.html#ixzz3ERL6WDd3

Need to replace the dampeners on it should be two of them one on each side

not any more but be sure you put it the wright way or you will doing it all over again.

I am not a specialist on the subject but am aware that an A/C takes as much as 20 to 25% of power from an engine. It therefore makes me think that if your car is in need of a service and/or if some kind of service or age related problem exists, then when you switch on (use) the A/C the 20 to 25% power loss is exacerbated by the inherent problem resulting in the current problem you experience. I suggest you have your car checked on an engine analysis machine at a Honda Dealer or reputable motor workshop.

What sensor? What code?

It would take someone with a scan tool and some experience to watch O2's to see if the CAT is functioning properly. If you have a code that is pointing to an non efficient CAT check for exhaust leaks before CAT

Wow, often people have no clues or details as to what is wrong....well you sir win the "covered all my bases" medal as far as I am concerned.....Sorry I can't help.