Honda Accord - Recent Questions, Troubleshooting & Support - Page 6

bad fuel damaged engine bearings rod piston crank cam timing slack timing off cam actuators etc check for trouble codes

no inertia switch check relays --module short possible burnt them out

Its called a Main Fuel Pump Relay.. It controls Fuel Pump, Starter, Ignition.. and Like 12 things.. Get one And I guarantee that'll fix it.. It looks like a cell phone on the upper inside of the dash.. about 52 Bucks from the dealer.. Try it

Sounds like the buttons are dirty. Remove the unit and remove the case. Clean the switch contacts with electrical switch / contact cleaner spray. Clean the connectors as well. If that doesn't work, take in for car audio repair.

It appears to be a known issue! https://www.google.com/search?q=2005+Honda+Accord+alarm+system+won%27t+turn+off I would take it to a good vehicle electrician who has a good scan tool computer to test diagnostics on the whole electrical system.

Hi,

Most Honda ABS warning light will blink in 2 parts, main system and then sub system to form the code pair. As an example is 3 blinks then 3 blinks is a code 3-5. Once determined, reference below listing.
1 - ABS pump motor over-run
1 2 ABS pump motor
1 3 high pressure leakage
1 4 pressure switch
1 8 high pressure system
2 1 parking brake
3 1 pulser RF
3 2 pulser LF
3 4 pulser RR
3 8 pulser LR
3 12 different diameter tires
4 1 wheel sensor RF
4 2 wheel sensor LF
4 4 wheel sensor RR
4 8 wheel sensor LR
5 - rear wheel lock - R/L
5 4 rear wheel lock - R
5 8 rear wheel lock - L
6 - fail-safe relay - F/R
6 1 fail-safe relay - F
6 4 fail-safe relay - R
7 1 solenoid - RF
7 2 solenoid - LF
7 4 solenoid - R
8 1 ABS function
8 2 CPU comparison
8 4 IC self-check

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

You got the Wrong Information! Go to Wal Mart and Purchase a "Bulldog Security Keyless Entry" System for your Car. It will cost you a Quarter of the Price and is Just asw Reliable as the Factory Unit! Got one on My Truck with Remote Start also and it works GREAT! Should cost about $50.00 Bucks or so.

then replace it

try checkin your idle air control. most of the time it is a vacuumn line going into intake.pull it off and if the car revs up dont worry, it wont hurt it. if it does simply put it back on, if it dies you have a bad vacumn.

HEADLIGHT REPLACEMENT1. Remove the front bumper 2. Disconnect the connectors (A).3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).Fig. 21: Removing Mounting Bolts & Headlight Assembly

buenas tardes el estereo de mi accord 2005 se bloqueo y en el U sale 1222 y L 7575 pero solo trae del 1 al 6 como meto ese codigo

There could be a number of reasons the car isn't starting. Is your check engine light on? If it is, the problem is likely a bad sensor or electronical problem. If the check enginie light is not on, it may be a vacuum line, plugged fuel filter, worn fuel pump, or other non electrical related problem.

Hello. Your Honda needs motor mounts; possibly all 3 motor mounts AND a transmission mount(s). Usually bad vehicle motor mounts allows 'vibrations' to be felt. In rare cases, the engine will 'dangle' because motor mounts 'snapped' and there is nothing there to keep it in place. Good luck and keep me informed; if you want to.

Hello. It seems the heat control is either set too low and/or the heating element in your seats are inoperative. Check your heat control knob setting first. Good luck and keep me informed; if you want to.

Hello. There are 4 speed sensors; one at each wheel. They are mounted close to their respective wheel. Speed sensors count the revolutions of their respective wheel and sends that information to the ECM/PCM. This information is 'averaged' and displays on the speedometer. Good luck and keep me informed; if you want to.

https://www.fixya.com/answer/answerpageslideview.aspx?ctg=mine&fml=0&brd=0&thid=29836379#moderation-modal

https://f01.justanswer.com/dcraig1000/c3fd2636-c8a3-4191-9251-69b0a67f5250_eee.pdf

You need the fault code read that triggered the light to come on.

If you have no pulse at crank position, but do at the run position. Replace the ignition switch.

valve clatter is usually the sound of oil starved valves if lite came on would indicate no oil pressure --check oil level and have oil pressure tested