Dodge Durango - Recent Questions, Troubleshooting & Support - Page 3
2007 dodge durango, will turn over won't start, ck
2006 Durango turns over and won't start. After a few try's to get the vehicle started the vehicle will have no power. After sitting for a few minutes the vehicle will start.
Has anyone experienced this?
10/25/2022 10:54:36 PM •
2007 Dodge...
•
Answered
on Oct 25, 2022
2000 Dodge durango wont start after driving for a while.
i had the same problem in a dodge ram pick up. ended up being the coil. when the coil got hot my truck would die or not start again until the engine had cooled down. replaced the coil, and whalaaaaah. no more trouble. good luck!!!!!!!!!!!!!!
2001 durango door lock relay
Look under the Hood and Locate the Fuse Relay Box. The Relay for these is in this Box. They are Just small Black Squares that Pull out. They Just cost a Couple of Bucks Each. The Diagram for these Should be Either inside the Cover for the Fuse Relay Box or In the Owners Manual. Please Rate My Response! Thanks!
No voltage to o2 sensor fuse '99 durango
no symptoms told is engine dead, or is DTC for O2 set.?
no clues told to put helpers on target.
are you asking which fuse blew or why it did.?
a fuse has 2 end both ends are 12vdc key on
if one end is now 12v but near 0v the fuse is BLOWN
no better test exits. doing that with a DMM. (a live test)
well the fuse is blown and 02 love to short the 2 heater pins
or wires at it burned and shorting, loves to....
no engine told so exact answers are not possible
the service manuals are by country ,year, make,model, engine and transmission, if driveline problems and is.
gen 1 is DODGE:
3.9 L (238 cu in) Magnum V6
4.7 L (287 cu in) Power Tech V8
5.2 L (318 cu in) Magnum V8
5.9 L (360 cu in) Magnum V8V6
USA drawings, show.
OXY fuse is
Fuse A1 , 10 amps. a1 is hot if ASD is not dead keyon.
same fuse A2 if A1 is hot, and A2 is dead, the fuse A1/2 is blown
all 4 OXY sensors run off that one FUSE
now lets talk why pin A1 WOULD BE DEAD
WELL THE ASD IS DEAD. IS WAY .
ASD GOES DEAD FOR ONE PRIME REASON, SPARK IS DEAD.
THIS MAGIC LOGIC IN THE PCM PREVENTS CRASH AND BURN.
3 CAUSES ARE.
1: PCM SEES ANY COIL SPARK FAIL (DETECTED)
2: PCM SEES CMP DEAD.
3:PCM SEES CKP DEAD.
OR PCM FUSES BLOW, TO IT. SURE
. PCM RUNS ASD ALL BY ITSELF AND ITS RULES.
Why not start problem by telling it first.
engine dead, cranks ok.?
or runs for 1 to2 second and ASD drops and sure stalls.
Replace egr valve on 2003 durango
Hi thanks for your question' The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,
- Remove electrical connector (5) at top of EGR valve solenoid.
- Remove tube mounting bolt (1) at intake manifold.
- Remove two bolts (4) connecting EGR tube (1) to valve assembly.
- Remove gasket located between EGR tube flange and EGR valve assembly.
- Remove two EGR valve mounting bolts (5).
- Separate valve assembly (3) from engine.
- Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
- Clean area at rear of left cylinder head where it joins base of EGR valve.
- Clean EGR tube where it joins EGR valve.
- Position new gasket between EGR valve and cylinder head.
- Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
- Position new gasket between EGR tube flange and EGR valve assembly.
- Position EGR tube (1) to side of EGR valve and into intake manifold.
- Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
- Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications
How do you fix a
P0562 is a system voltage low. Most likely the alternator has failed.
Location of valet/override button on dodge durango 19999
The valet/override button is located right under the steering column on your 1999 Dodge Durango. To reset the alarm, press and hold the button within five seconds of cranking up the engine - release it when the security lights stop blinking.
2000 dodge durango cooling issue: I HAVE THE 5.2L
Ihave a 2000 Dodge Durango i have put a new radiator and the gaskets came back good um i replaced the coolen fan also the thermostate and tested it it it came back good when i run it its fine but when i am in line its hot when i drive it cools down........
98 Durango 4x4 5.2
Get code crank-cam lose
Could be in the wiring, then, for those 2 sensors. I think they would both share the same 5 volt reference signal from the computer. When it stalls or goes into popcorn phase, a digital voltmeter (multi-meter) might help catch the missing signal, or it could be a poor connection for the ground for those two sensors, also. The ground connection would be known as an engine wire harness ground. But you can check the ground wire integrity at the sensor connector also.
To check the reference signal, ground voltmeter black lead to negative batt. terminal, and voltmeter red lead to sensor connector on the reference wire terminal (there's only 3 wires: reference (5 volt) wire, ground wire, and sensor signal wire to computer). Then turn key to ON. You should see very close to 5 volts at one of those terminals. If it had stalled and you had no signal, you would have to trace that wire back to the computer. By and by, you will probably need a wiring diagram.
I have a 1999 Durango that had an exhaust leak on
It can be a daunting task. You'll need to center punch them as deeply as possible. Use left handed cobalt bits starting with the smallest possible bit & work your way up to about 3/4 the size of the bolt & try an easy out. Don't break the easy out!! If the easy out fails,continue drilling to the proper size for a heli-coil & install one. Use anti-sieze on the new bolts. If this fails,hate to say it,remove the head & try a drill press.
Not finding what you are looking for?