no engine told at all. (i will answer for USA spec, cars only)a Generation 4 car.such an easy problem. any car the fails parked is easy to diagnose and 10x more safe to do. 2 engine, offered day1 new. which one is it.3.3 L V63.8 L V6Ever fix an engine that only fails down hill in left turns only.see?hood up.not told you, does the starter crank the engine fast when dead.?called a no crank engine, or is way too slow ,weak battery.aka. cranks fast but will not start.you have 2 hours to find it, easy no?1: we test for spark first. google how to test spark. 100 years its the same way..do not ever scramble the 6 wire coil pack wires.2: ok spark is good we use spray test fuel (in a can) called instant start in a can, does it start now?yes. but runs 3 seconds and stalls.3: fueling is bad, we just learned. if will not run step 2 that is a bad engine,easy no? just simple tests so far.next comes fuel pressure. test at the fuel rails using fuel pressure test gauge. (a tool) 55 and 49psi chart above order. spec.keep in mind it can be just 1 rusty wire, wrongnot replacing by guess 10 or 20 good parts and now broke.it can also be bad fuel or dead fuel pumpand lots and lots more, but we do the tests in orderto find the cause, and more tests. watch scotty yethttps://youtu.be/064Ilsz8Fzg
In this model, the TCM is often located near the transmission, mounted on or near the transmission housing. However, exact locations can vary slightly depending on the specific vehicle configuration. It's advisable to consult the vehicle's service manual or a qualified mechanic for precise information on locating the TCM in your specific vehicle.
Spare wheels are no longer required due to the torque setting to remove a wheel and the use of sealants that inflate a flat tyre for a limited period of time allowing one to get the tyre repaired/replaced.
Space saving comes straight to mind.
That is called the Exhaust Manifold. One side is attached to the side of the engine, and the other side is attached to the end of the Catalytic Converter. If the car is horrendously loud, someone has stolen it. If you can see it under the van, the gaskets just need replacing or the bolts tightening. The Cat often has a flex pipe which can split, in which case it needs replacing.
If it is a petrol engine, check the Octane of your fuel and if correct suspect the ignition timing.
Don't run it like that for long as damage may occur to the pistons.
When you say the "oil light," do you mean the light that says "Change oil" or are you seeing the red light that indicates low oil pressure? If you're seeing that red light, that likely means you have low oil pressure and should stop driving immediately, until the problem is diagnosed and repaired. It's also possible to see the oil pressure light on when there's no issue with oil pressure, if the oil pressure sender has failed or there's a connection problem.If the oil light you're referring to is the "change oil" light, you will need to manually reset it for it to disappear. Here's how (from Chrysler):1. Turn the ignition switch to the ON/RUN position (do not start the engine).2. Fully depress the accelerator pedal, slowly, three times within 10 seconds.3. Turn the ignition switch to the OFF/LOCK position.NOTE: If the indicator message illuminates when you start the engine, the oil change indicator system did not reset. If necessary, repeat these steps.
Question edited for clarity.
Question moved to model category.
It does have a low pressure port,. It has to for the pressure gauges set.
The low side valve is on the suction line, near the washer fluid reservoir filler.
Jun 2, 2011
troubleshoot this further:
Check Transmission Fluid:
The first step is to inspect the transmission fluid. Low or contaminated fluid can lead to poor shifting performance. Ensure the fluid levels are adequate and replace it if necessary.
Throttle Position Sensors and Shift Solenoids:
Misaligned throttle position sensors or malfunctioning shift solenoids could be causing the gear shifting problems. These components play a crucial role in proper gear changes. A professional diagnosis is recommended. It is not unusal for a defective solenoid to render this effect.
Transmission Control Module (TCM):
The TCM manages the transmission's operation, including gear shifting. If it's malfunctioning, it can lead to incorrect or no gear shifts. Consider checking or replacing the TCM.
Shift Linkage or Cable Issues:
Damaged or worn shift linkage or cables can also cause gear shifting problems. These components connect the gear shift lever to the transmission. Inspect and replace any damaged parts.
Remember that diagnosing transmission issues usually requires professional expertise.
That is a transmission issue Glenda. The Diagnostic Trouble Codes tell you the problem and from there, the fix. You need to get the codes and post them here. Garages will normally tell you the code for free in in the hopes in getting the work, or AutoZone will do it outside the shop.
..
I found a forum post on Jeep Enthusiast Forums that provides the tightening sequence for the 3.8L upper intake plenum of a 2007 Chrysler TWC. Here are the steps:
Remove covering on lower intake manifold and clean surfaces.
Inspect manifold gasket condition. Gaskets can be re-used, if not damaged. Position new gasket in seal channel and press lightly in-place. Repeat procedure for each gasket position.
Position upper manifold on lower manifold.
Apply Mopar® Lock & Seal Adhesive (Medium Strength Threadlocker) to each upper intake manifold bolt.
Install and tighten bolts to 12 N·m (105 in. lbs.) using torque sequence.
Here is the torque sequence for the 3.8L upper intake plenum:
6 2 4
5 1 3
Please note that this information is provided as-is and I recommend consulting a professional mechanic for any further assistance.
Question edited for clarity.Question moved to model category.Electronic Throttle Control issue. The car isn't letting to go anywhereElectronic Throttle Control IndicatorElectronic Throttle Control IndicatorThis is the Electronic Throttle Control (ETC) Indicator symbol. This light, a lightning bolt between reversed brackets or parenthesis, will illuminate if there is a problem in the electronic throttle control system. It may be seen in red or yellow/amber. As an electronic system, it can sometimes be reset by restarting the car, much or exactly like re-booting a computer.Before moving on, are you sure this is your symbol?? If yes, then continue on below. Otherwise return to our main Picture Symbols page and scan again!If the system and the light do not reset with a restart, the vehicle should be drivable, but your dealer or authorized service center will need to service the system soon.Note however, that if your vehicle does not operate normally, contact roadside assistance right away.https://dashboardsymbols.com/2019/06/warning-lights-and-symbols-seen-in-chrysler-vehicles/..
If you're seeing that red light, that likely means you have low oil pressure and should stop driving immediately, until the problem is diagnosed and repaired. It's also possible to see the oil pressure light on when there's no issue with oil pressure, if the oil pressure sender has failed or there's a connection problem.If the oil light you're referring to is the "change oil" light, you will need to manually reset it for it to disappear. Here's how (from Chrysler):1. Turn the ignition switch to the ON/RUN position (do not start the engine).2. Fully depress the accelerator pedal, slowly, three times within 10 seconds.3. Turn the ignition switch to the OFF/LOCK position.NOTE: If the indicator message illuminates when you start the engine, the oil change indicator system did not reset. If necessary, repeat these steps.
