BMW X7 Series - Recent Questions, Troubleshooting & Support


these cars are very complex--buy a haynes manual for troublshootn--du a scan that runs a data stream and never ever bringit to a dealer

1997 BMW 7... | Answered on Feb 27, 2019


On this website you find fuse box diagram and description for BMW 7-series

https://www.autogenius.info/category/bmw/7-series

1990 BMW 7... | Answered on Nov 11, 2018


have you put a different type of power steering fluid?

in some instance, if they put a different type of fluid, the solution bubbles up and makes a whining noise when you use the car.

tnx 4 using fixya,

drcool

2000 BMW 7... | Answered on Nov 06, 2018


Check this website, you find there fuse box diagram and description for BMW 7 Series

http://www.carknowledge.info/category/bmw/7-series

BMW X7 Series... | Answered on Jun 30, 2018


I think you should go for repair manual first. After that you can easily repair your car by yourself.I had visited this site past 2 months before for my vehicle and find it quite helpful may be you will also get something useful here.They offer cheap prices and also discount too
Best Manuals

1997 BMW 7... | Answered on Mar 20, 2018


If you're comfy with manuals then i know few websites that can help you with it. Bcause I've got it from various
websites so I know how each site deals. try www.reliable-store com . Very helpful

1993 BMW 7... | Answered on Mar 07, 2018


The replacement starter may have required installation of shims to ensure correct engagement with the flywheel and that wasn't done. Also, the replacement starter could have been a look-alike-but-not-function-alike item.

1987 BMW 7... | Answered on Jan 30, 2018


you need a monitor upgrade

2000 BMW 7... | Answered on Jan 30, 2018


1998 bmw 740il
My personal suggestion would be to go for these repair catalogs. I know this website reliable-store that i used to buy them from, and they sold online it was very good manual. Go ahead, I bet.

1997 BMW 7... | Answered on Jan 26, 2018


You need to wait 1 hour before attempting to put the code in. Either the ignition needs to stay on 1 hour or drive it for 1 hour. If they key is turned off before then, you will need to start again.

1989 BMW 7... | Answered on Jan 24, 2018


Check fuel pump pressure

1993 BMW 7... | Answered on Dec 31, 2017


indicates a brake master cylinder internal failure
take it to a brake specialist shop for a proper diagnosis
If the brake system has not seen a service or component for the past 5 years , a replacement master cylinder is the professional fix

1994 BMW 7... | Answered on Dec 07, 2017


Get the gearbox serviced before it becomes very expensive.

1998 BMW 7... | Answered on Dec 05, 2017


I would check the fuel pump. fuel deed, filters and pump relay.

1994 BMW 7... | Answered on Nov 24, 2017


Here are some suggestions...
For fault 140 thermostat you may also want to check thermostat wiring connector by t-stat and also DME (disconnect inspect clean)
For fault 185 leakage... try this; The wiring to the Fuel tank leak pump chafes on the L/R inner fender liner and cuts the wire in half or opens the insulation and the wire corrodes. Pull the L/R wheel and then remove the fender liner. You will probably see a spot on the liner where the wire has rubbed. Find the break in the wire and fix it. Reroute the wire so it does not chafe again.
For fault 106 replace the brake light switch under the dash

2000 BMW 7... | Answered on Nov 02, 2017


find the pin from bmw/becker or whatever unit you are running.
this is to prevent theft of auto systems.

1989 BMW 7... | Answered on Oct 28, 2017


The usual culprit is the water pump. If you have gone 175k without a new one that is almost amazing; I replaced the one on my 325xi at about 135k. If you are a DIYer, do a youtube search on replacing the pump on a '92 735 to see if you want to take it on. It was super easy on my '02 325. If you can reach the pulley and the pump is bad, you can probably wiggle it. If it moves at all the pump is bad. You might need to go so far as to remove the belts to check. If the pulley is plastic then replace it with the pump as it will likely have a few craks (sic - correct spelling is considered profanity on this site) and may even break taking it off the old pump. I've had good luck with both FCP Euro and Pelican Parts for both quality and prices on parts. One other thing, shortly after replacing my pump I developed a crak (sic) in the expansion tank which will also leak coolant (and cause overheating if you don't keep your radiator topped off) so check that too, maybe even first. Replacing the tank was actually more difficult because after undoing the hoses the tank did not want to pop out but it would be of a different design on your car.

1992 BMW 7... | Answered on Oct 22, 2017


hi,i own a bmw 750i,and went over a hump back bridge to fast and left the ground a bit.since then the rear suspension is jacked right up high permanently and makes a screeching sound like gas is escaping...any ideas??

1988 BMW 7... | Answered on Oct 08, 2017


I would get a connector that is a heat shrink type and put them in it and crimp them in it all together and seal it by heat shrinking the ends.

1984 BMW 7... | Answered on Oct 07, 2017

Not finding what you are looking for?

-681 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 BMW 7 Series
1998 BMW 7 Series

-97 Questions

2000 BMW 7 Series
2000 BMW 7 Series

-66 Questions

2002 BMW 7 Series
2002 BMW 7 Series

117 Questions

1997 BMW 7 Series
1997 BMW 7 Series

88 Questions

2003 BMW 7 Series
2003 BMW 7 Series

91 Questions

Top BMW Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

80stech

Level 2 Expert

120 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

BMW Cars & Trucks

  • Forum

View Most Popular

  • BMW Cars & Trucks
Loading...