Yamaha ATVs - Popular Questions, Answers, Tips & Manuals

Question edited for clarity. Question moved to model category. It is a Speed Sensor issue. https://www.google.com/search?q=yamaha+big+bear+flashing+red+brake+light+on+dashboard ..

Question edited for clarity and add maker. Question moved to a Big Bear category. Chat GPT4 Answer from AI Bot 'Gerry' deleted. Mikuni tuning in the link. The screw is under the intake bell. https://www.google.com/search?q=mikuni+bsr33+carburetor+tuning ..

Service manuals show 15 mentions of relay https://www.google.com/search?q=2000+yamaha+kodiak+400+4x4+service+manual .. https://www.google.com/search?q=2000+Yamaha+Kodiak+400+4x4+relay+locations ..The video says it tests all 3

Could be fuel starvation caused by dirt in the filter/carburettor etc.

Get a battery tender to put on the battery when you aren't using it to keep it fully charged. Check battery connections and grounds. Check the starter relay plus the starter and solenoid. Call an auto electrician. The videos may help diagnosis.

The cold weather may cause your Yamaha Timberwolf to experience hard starting, several months and no use, or a stale fuel supply. Start by replacing the spark plug, if the engine still does not fire up, clean the carburetor and make sure all the hoses are connected tightly with no air leaks. If none of these strategies work, the carburetor may need to be adjusted or replaced. You may want to take it to an experienced mechanic if you are unable to get the engine started.

Question edited for clarity. Question moved from motorcycles to ATV model category. Turning over has nothing to do with the carburetor! Your battery is flat. It will need charging. If the carb is leaking, it is because the float is set wrong or the float valve needle isn't seating properly. Engines only need three things to run. A supply of clean fresh fuel (not sitting a year) A Spark at the right time. Compression. You say you cleaned the carb **in** carb cleaner, as opposed to *with* carb cleaner. Did you strip it down, check the float for holes, clean the jets and needles?

ATV IS NOT A CAR NOR IS ATV A MAKER IS THIS A YAMAHA WHY SKIP SAYING MAKERS NAME/? RAD FULL OF MUD (AS IN FINS) THERMOSTAT IS BAD. SORRY CAN NOT GUESS ATV AT ALL, AND 300 SAYS ONLY ENGINE SIZE, TO ME. 300CC

If the CV Joints are new and correctly inserted, the most likely culprit for the noise would be the brakes. Remove the front wheels and turn the hub. It could also be the front differential, or failed wheel bearings. Details in the link. https://www.google.com/search?q=Yamaha+big+bear+350+4x4%2C+front+wheels+grinding+noise ..

https://www.manualslib.com/manual/828205/Yamaha-Yfm400far.html

not car moved you to ATV

Question edited for FULL 'make model (what it is)', from 'banshee'. Question moved from Motorcycles to correct Category. Check spark plugs. Clean Carb. Check timing. More here, it is a known issue. https://www.google.com/search?q=Yamaha+banshee+atv+backfires ..

Question edited for full 'year make model (what it is). Question moved from motorcycles to make model category. Please don't type in all CAPS, it is considered SHOUTING and is harder to read. 'clips' and 'turns' it took me a while to realise you were talking about the carburetor and you were playing with the mixture screw and needle position! 4 turns out is a lot different to the factory setting which is 1 1/2 turns out. If it is overheating it is running too lean. As you changed the stator, also consider the ignition timing. Popping can also be caused by the ignition failing under load, coil, lead and spark plug. Carburetor and tuning. https://www.google.com/search?q=2004+yamaha+yfz+450+carburetor+adjustment This carb has a LOT of jets! https://www.amazon.ca/Carburetor-Rebuild-Yamaha-YFZ450-2004-2009/dp/B07JNYP667 ....

NOT CAR, MOVED TO ATV BUY THE SHOP SERVICE MANUAL FROM YAMAHAMMER.

Question edited for clarity. Question moved to model category. Just replace the relays. They are cheap! https://www.google.com/search?q=2000+Yamaha+Kodiak+replacement+relays ..

Question edited for clarity. Add maker. Question moved to Yamaha Bruin category. Likely to be a fault with the ignition switch Karen. There is help in the link. https://www.google.com/search?q=2004+Bruin+350+won%27t+switch+off ..

Question edited for clarity, full make model (what is is). Question moved from 'Office Equipment' to Yamaha sub category. All mentioned here. I would stick with 33.1 degrees. https://www.wolverineforums.com/threads/tilt-to-roll-over-degree.29718/ https://www.google.com/search?q=2021+4max+1000%2C+tip+over+angle ..

Need to inspect wiring going to main power for wire shaffing you have a direct short to the frame some were

get a colortune tool.it shows how your firing.read instructions that come with,so simple to tune carb in with.sounds like pilot out of adjustment.could also have a leak in ur carb boot or head.take a torch without lighting open valve with motor running run torch around gaskets and front of carb boot listen for change in motor.if it gets higher rev uve found a leak.

We need a little more details... what/where is clicking..is the engine running when the clicking happens.. more details