20 Most Recent
Honda 2010 FourTrax Rancher 4X4 ES Questions & Answers
ATV will not start battery seems to be ok as lights are bright when turned on when key in on position.
What clicks is the solenoid for the starter. I pushes the starter gear into the flywheel, then the starter motor is supposed to spin the flywheel and it starts. If you hear the click, but nothing else happens, there is a good chance that it is the starter itself. Check the wires going to the starter and make sure that the red one is 12 volts. The black one should go to ground. If it has 12V on it, then it is the starter motor. If it DOESN'T have 12V, then the problem is that power is not getting to the motor.
2002 rancher 350 es wont shift and will shift manualy
sounds like one of your solenoid in the valve body is bad, if you.are able to shift it.by yourself, then it could be a.solenoid, but also.check your transmission fluid to make sure its full, check when transmission fluid is hot, either in park or neutral, your owners manual will tell you which.way to check it, sometimes on the.dipstick it will say how to.check it to.
Honda atv troubleshooting
Be sure the plug at the rear of the engine ic properly attached and clean. It gets knocked off easily.
4/21/2019 3:19:35 PM •
Honda ATVs
•
Answered
on Apr 21, 2019
Honda rancher
take the choke out of the carb using a 14mm wrench. The choke is a plunger held into the front of the carb by a plastic nut. Lubricate it and put it back. Be careful not to overtighten the plastic nut.
10/27/2017 2:20:13 AM •
Honda ATVs
•
Answered
on Oct 27, 2017
How To Use The Honda TRX 250X SportClutch
This video will explain what the Honda TRX 250X, 250 EX SportClutch does and how to use it. This video will help to answer what does the Honda SportClutch do; do I need to know how to use a manual clutch to ride the 250X, or is it an automatic. We answer these questions in this video for you.
New trans but no power
I assume it a honda with auto trans,,,, if so needs new oil pump,,, thats what makes tthe trans work it supplies the oil to the trans so it can make presure to work
11/26/2014 12:57:46 PM •
Honda ATVs
•
Answered
on Nov 26, 2014
Free atv troubleshooting
out of gas, clogged petcock, fuel filter or stuck carb float. assuming you're getting a spark still of course. that's a whole other can of worms
2/10/2014 4:18:42 PM •
Honda ATVs
•
Answered
on Feb 10, 2014
Assembly diagram for a recoil on a 1999 Polaris 400 xplorer
Assembling a recoil system on a Polaris 400 Xplorer involves several steps. While I can't provide an actual diagram here, I can outline the general steps involved in assembling a recoil system:
- Preparation: Ensure you have all the necessary parts for the recoil assembly including the recoil starter, recoil housing, recoil spring, and any other associated parts.
- Mounting the Recoil Housing: Begin by mounting the recoil housing onto the engine. It typically bolts onto the engine casing.
- Inserting the Recoil Starter: Place the recoil starter mechanism into the recoil housing. It usually fits into grooves or mounts within the housing.
- Attaching the Recoil Spring: Connect one end of the recoil spring to the recoil starter mechanism and the other end to a fixed point within the recoil housing. This provides the tension necessary for the recoil starter to function properly.
- Installing the Pull Cord: Thread the pull cord through the hole in the recoil starter mechanism and tie a knot at the end to secure it. Wind the pull cord around the recoil starter as per the manufacturer's instructions.
- Testing: Before completely sealing the recoil housing, give the recoil starter a few pulls to ensure it functions smoothly and retracts properly.
- Final Assembly: Once you're satisfied with the recoil assembly, bolt down any remaining covers or components to secure the recoil system in place.
Always consult the specific service manual for your Polaris 400 Xplorer for detailed instructions and diagrams tailored to your exact model. Additionally, if you're unsure about any step, it's best to seek assistance from a professional mechanic or someone experienced with small engine repair.
4/20/2024 12:13:30 PM •
ATVs
•
Answered
on Apr 20, 2024
Can't find how to trouble shot the horn on my 2015 Kawasaki mule
take off the horn unit power it direct if it works its ok, if not replace, next step wire a small bulb into the horn wires and press the button if it lights the switch is ok, if you have a circuit tester put one end on the battery ground and check for power in the horn wires if their is power there put the lead on battery positive and press the horn button if there is no power their the switch or wiring is faulty
4/16/2024 10:19:40 PM •
ATVs
•
Answered
on Apr 16, 2024
Not finding what you are looking for?