Kymco 2004 Mxer 150 - Answered Questions & Fixed issues

this is not a car or truck

Kymco 2004 Mxer... | Answered on Mar 15, 2016 | 581 views

do you have internet where you live? Try this
"2002 Polaris trailblazer users manual"

ATVs | Answered 17 hours ago | 43 views

Yea, what you said == just google it.

ATVs | Answered 17 hours ago | 21 views

Usually, there is a hole plug near the bottom of the casing. BUT first drive it around a lot cause gear oil is heavy and it won't come out very fast if it is cold.

ATVs | Answered 17 hours ago | 31 views

power to efi module? no, find where it stopped and reconnect.
yes, power out of efi module? no, replace efi module.
yes, open between efi and pump.

ATVs | Answered 20 hours ago | 26 views

search engine are more efficient. If this isn't to your liking
try searching "clutch nut torque spec"

ATVs | Answered 20 hours ago | 14 views

I don't understand your problem. What is a "make end"?

ATVs | Answered 20 hours ago | 12 views

are you into troubleshooting? Probably not, but one must have fuel, ignition, and air to make things burn or run an ICE.
What don't you have?
Is there an ignition source? Did you pull the spark plug and verify it will spark?
Is there fuel? No, not in the tank, it must be getting to the engine.
Is the spark plug wet? If it isn't wet with fuel, you are not getting fuel.
Is there air? No, not what you are breathing, but getting to the carburetor. Did you check the air cleaner?

ATVs | Answered 20 hours ago | 14 views

It acts like you have burnt spots on the starter shaft that touches the brushes ( voltage) to start. When you rock the vehicle in gear the starter shaft moves and it is placed in a position where the brushes can make a clean contact. Then when you turn the key, the starter will engage and the vehicle will start. My recommendation would be to change out the starter.

ATVs | Answered Yesterday | 41 views

check wire harness for short

ATVs | Answered on Oct 10, 2019 | 35 views

It sounds as though your ignition switch is not hooked up correctly. Follow the harness from the ignition switch to the bullet connectors under the front body plastic. Make sure the colors all match up.

ATVs | Answered on Oct 08, 2019 | 27 views

Even though the overflow is full, the radiator could be empty. You need to remove the radiator cap and make sure it is full to the top. If you find the fluid level is low in the radiator, that would indicate there is a leak in the hose between the radiator and the overflow tank.

ATVs | Answered on Oct 08, 2019 | 30 views

If you bypass unit will not run

ATVs | Answered on Oct 03, 2019 | 31 views

Check rear drive shaft from engine to rear differential.

ATVs | Answered on Oct 03, 2019 | 28 views

Verify spark and fuel.

ATVs | Answered on Oct 03, 2019 | 22 views

Did you check to see if the chokes on?

ATVs | Answered on Oct 02, 2019 | 38 views

Not finding what you are looking for?
Kymco 2004 Mxer 150 Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Kymco ATVs Experts


Level 3 Expert

85178 Answers

 Scott Tx
Scott Tx

Level 2 Expert

604 Answers

john h

Level 3 Expert

22408 Answers

Are you a Kymco ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides